• FrankHarlan
    Contributor - Level 2
    2019-10-02

    I can here a signal from the HF driver, but nothing from the LF driver. I have updated the firmware and it did not fix the problem.  Any suggestions?

    0 197
    • FrankHarlan
      Paul_Vannatto


      @FrankHarlan wrote:


      I can here a signal from the HF driver, but nothing from the LF driver. I have updated the firmware and it did not fix the problem.  Any suggestions?





      Hi Frank,


      Welcome to the forum. Have you had a look at the EQ or crossover settings in the DSP? It may have a very high high-pass setting.


       

      • October 2, 2019
    • FrankHarlan
      MatteoBarbaro

      Hi Frank,



      I think that shoud be the connector between the amplifier and the LF speaker, if you don't solve the problem with the suggestions of Paul of course. Remember that iQ loudspeakers are Two way biamp, so you have two amplifier output, one for each way.


      If it's in warranty i suggest you to contact your reseller.



      Regards,



      Matteo

      • October 28, 2019
  • BobKraus
    Contributor - Level 1
    2019-07-19

    I have been trying to get this to work using the instructions, but they just seem to be missing a step. I would like to use the Turbo Control App to control both of my IP1000s, but I can only seem to get one to be controlled. The Master/Slave feature doesn'r seem to work either... Any help?

    read more...
    0 195
  • scredly
    Contributor - Level 2
    2019-10-09

    Is there a button/power sequence to reset an IP2000?   Out of nowhere, the input sensitivity of one of my units is out of whack.   One unit volume is at 4.5 and the other is now at 26 to match it.     

    0 189
  • dhsherbert
    Contributor - Level 1
    2019-06-25

    Hello!

    I just purchased a Turbosound iP300 and had a question that is not addressed in the Quick Start Guide. I'll be using this speaker with my Laptop, Audio Modeling SWAM Wind Instrument software, EWI5000 and Focusrite Scarlett 2i2 Audio Interfacel. I need to use both Left & Right output signals from the Focusrite. Is it OK to use both Inputs of the iP300 for this?

    Thank you,

    Doug

    read more...
    0 181
    • dhsherbert
      KenMitchell

      Hi Doug ( @dhsherbert ), 


       


      Sorry no one replied to you earlier.  I just stumbled upon this when I was looking at your reverb question.  Yes, there's no issue with connecting to both inputs on the IP300 at the same time, whether it be from the same interface of different interfaces.


       


      Hope this helps, 


      Ken


       

      • August 13, 2019
  • mmccutchen
    Newcomer - Level 1
    2020-06-21
    I have two IP2000 speakers and one works fine but the other has very little volume and sound seems to break easily. Looking for advice since I have little knowledge about speakers.
    0 180
    • mmccutchen
      GaryHiggins Hi, the only advice to start anyway is duplicate every setting from the working one to the faulty one, if no improvement, you may need to put in a CARE ticket to have it repaired.
      • June 21, 2020
    • mmccutchen
      GaryHiggins The gain settings need to be equal, dsp etc. Easy to skip one by mistake.
      • June 21, 2020
    • mmccutchen
      AlexLane Try Performing a factory reset;

      Hold down the encoder Knob and Setup button while powering on the unit, follow all the on screen test instructions.
      • June 23, 2020
  • dhsherbert
    Contributor - Level 1
    2019-08-12

    Hello!

    I have an iP300 that I use with my EWI5000. It is stated that the iP300 has Reverb/EQ, but I can not find how the control the Reverb (and neither can the Tech Support for Sweetwater Music). Can anyone help?

    Thanks!

     

     

     

    read more...
    0 176
    • dhsherbert
      KenMitchell

      Hi Douglas ( @dhsherbert ), 


       


      Welcome to tthe community. 


       


      Disclaimer: I don't have one of these in front of me.   From looking at the QSG on Page 9 and 10, it looks like you press the "Process" button, use the encoder to get to "Input", and then it gets fuzzy.  I can't tell if you press the encode knob to select or the "Enter" button to select.  Once selected, you should see Channel A, Channel B, and Channel BT.  Again, use the encoder to rotate through the options and then select it with whatever method you found above that works.  You should be able to adjust input level EQ and Reverb for A and B. 


       


      Hope this helps, 


      Ken


       

      • August 13, 2019
    • dhsherbert
      LiamArthurs

      Get the app - its is excellent ;- 2 screens and you have control- inputs vol FX Eq - EZ 

      • January 1, 2020
  • RettichProd
    Newcomer - Level 1
    2020-07-07
    Hello, we are located in Southern Ohio. We were wondering if Turbosound has released the Manchester series yet? Also, wondering if they’ve done any events concerning the Manchester series. We held off on purchasing a different brand because of our history with Turbosound TMS-3, Flashlight/Floodlight series...
    read more...
    0 174
    • RettichProd
      billygallagher Hi RettichProd, How are you. There are some currently some in stock so I would contact you sales rep.
      • July 8, 2020
  • percy777
    Newcomer - Level 1
    2020-10-23

    two years ago i bought a turbosound ip2000 speaker. then recently i heard that i could link turbosound speakers with each other. so i bought anoher turbosound ip2000 speaker. i had no idea there were two versions. the first one i boght was ip2000 version 1 then the 2nd one was version 2. my problem is i was trying to link the both of them but it wouldnt work. is it because these two have different versions? if so, how do i upgrde my ip2000 vrsion 1? your response would be a big help, stay safe and thank you!

    read more...
    0 173
    • percy777
      ChrisEdwards1 Hi Miquel, I hope you are well. Unfortunately, it is not possible to link a V1 unit to a V2 unit via Bluetooth. This can still be achieved via an analog connection, however, due to hardware changes, the V1 is not compatible with the V2. There is no official way to upgrade your V1 unit and please note any modifications carried out would void your warranty (If applicable)
      • October 26, 2020
  • oregandave
    Contributor - Level 1
    2019-10-13

    Just wanting to keep with the turbo sound brand and look and am looking for subs that would compliment the ip300s. Was looking at the ip12b but have no use for the extra power amps for passive tops and also would need a crossover from what I've been reading. Any help/suggestions would be very welcome.

    read more...
    0 159
    • oregandave
      oregandave

      Anyone ?

      • January 17, 2020
    • oregandave
      Diepsloot

      What is the main way you are using them? Mobile dj, solo musician, indoors, outdoors, corporate events? Maybe someone's ears might perk up to help if you are more specific and they can tell you what use they have given them. 

      • January 18, 2020
  • Ekm4489
    Contributor - Level 1
    2020-10-26

    Hello, 

    I'm searching for replacement pole mounts to go into my subs. Does anyone know where I can find some that would fit? I've tried a couple different sizes from On-Stage Stands and neither worked. 

    I prefer the M20 threads if they might be available somewhere, just looking for something to make my setup a little more secure. 

     

    Thanks for the help! 

     

     

    read more...
    0 153
    • Ekm4489
      ChrisEdwards1 Hi Kyle, I hope you are well. If you have not already done so I would recommend submitting a parts request, this can be done by going to support at the top of the page and scrolling down/clicking the parts tab. Once the form is filled in one of my colleagues will be in touch to advise further. Just make note that you are looking for a replacement Pole Holder / Top Hat and they will be able to assist further.
      • October 27, 2020
    • Ekm4489
      LeeE_Wolloff Kyle, I had the same issue and simply resized the on stage mounts to fit the smaller recesses of the sub. It worked well and the screw holes lined up perfectly. No modification of the sub.
      • November 1, 2020
Go to page