Statistics

242,665 members
119,061 posts
  • New
    stangeo20
    Newcomer - Level 1
    2021-01-12

    I bought a new xenyx QX2222USB mixer, but the USB input is not working with MacBook air. Is there any driver that needs to be installed? However the output to the mixer is working through the macbook. I called Apple and they referred me to Behinger website. Please help?

     

    read more...
    0 150
    • stangeo20
      RexBeckett Hi stangeo20, the QX2222USB is CoreAudio compliant so should work with your Macbook without any special driver. Two things to check: Make sure that the red USB/2-TR To Main button is not pressed as this will mute the USB recording feed; Check the Mic Privacy settings on the Macbook to ensure that your recording software is permitted to use the audio interface.
      • Jan 12
    • stangeo20
      stangeo20 Here is what I found out.

      I was using Behringer Ultralink ULM 200M USB microphone when I created this ticket. So I found that when I use the USB microphone there is no USB Codec signal coming into my MacBook for recording. However I tested today with another microphone and used an XLR cable and the USB codec worked absolutely fine.

      This leads to my next question, the mixer I bought was because it works with Behringer USB mic input. How can this be resolved that I’m able to use both XLR cable inputs and USB200M microphones?
      • Jan 13
      • Behinger xenyx QX2222USB mixer USB issue
        RexBeckett It sounds as though there could be a problem with the ULM200M rather than the mixer. Try connecting the USB receiver to a PC to see if it works that way.
        • Jan 13
  • jeffconnective
    Newcomer - Level 1
    2020-10-01

    I had two S16s connected (one as MASTER and the other as SPLITTER) and it worked for weeks. All of the sudden, they don't connect anymore. The AE550 light is blinking for channel A on both units, but it's intermittent and in no discernable pattern. Please help!

    read more...
    0 124
    • jeffconnective
      Nigel67 Hi Jeff. It could be the clock playing up on the master unit. None of the settings have been accidentally changed? For test purposes, have you swapped the clocking on the units, i.e made the slave the master and master the slave to see if that fixes the issue. How long is your stp CAT5E cable between the units? Due to the fact that the AES50 is flashing on both units, my initial thought would be that the Master unit is faulty. Do you have any other gear with AES50 connections on that you could sync up to each box to identify where the issue lies? Once identified, you will need to go to the support tab at the top of the page and submit a service request ticket and a colleague will be able to book the unit in for repair.
      • September 30, 2020
    • jeffconnective
      Paul_Vannatto I would strongly recommend trying another AES50 cable. I just consulted with someone the other day with similar symptoms and it was the cable at fault (yes they can go bad).
      • October 1, 2020
  • New
    tazzboy
    Contributor - Level 2
    2020-11-29

    I was wondering is it possilbe to hook the Motu 8pre with USB into the Behringer X-Touch usb port ?

    0 118
    • tazzboy
      DaveMorrison Are you asking about connecting the 8Pre's USB cable into the Built -in USB hub on the X-Touch so you have just one cable going to your computer? If this is the case case, the answer is Maybe. I've had good luck connecting audio interfaces through the hub on the X-Touch, but not everyone has. It depends on the computer's USB ports, the Audio Interface's USB interface, the USB cable, and some luck. In theory, it ought to work, but you have to try it on your system to know for sure.
      • November 29, 2020
      • Motu 8pre usb into Behringer X-Touch
        tazzboy Yes that is what I am asking the USB on the Motu is 2.0 So I was wondering since I have read on the manual that you can plug in a keyboard and mouse that has USB capabilities I thought I would ask to find out if you can do the same with a Preamp audio interface.
        • November 29, 2020
    • tazzboy
      DaveMorrison Give it try. You won't hurt anything and it might work for you.
      • November 29, 2020
      • Motu 8pre usb into Behringer X-Touch
        tazzboy True the only thing bad that might happen is that doesn't work at worse. Then again it might work and Behringer would smart to make it happen or letting people know.
        • November 29, 2020
      • Motu 8pre usb into Behringer X-Touch
        DaveMorrison It works for me, but it doesn't work for every one. I think that's why Behringer won't say it will.
        • 1
        • ·
        • November 29, 2020
      • Motu 8pre usb into Behringer X-Touch
        tazzboy Well I gave it try and didn't work for me. Oh well on to something else, Now I need to figure out to get the X-touch and Motu 8pre to communicated with one another when using.
        • November 29, 2020
  • Yoshaan404
    Newcomer - Level 1
    2020-10-22

    Hello, 


    Can I get a new power cable for the Behringer Deepmind 12? 

    Thank you,

    ~Harshaan

    0 101
    • Yoshaan404
      Yoshaan404 Not sure why Behringer's product service portal brings its customers to a music forum. How am I supposed to get a cable for the synth now? Do better.
      • October 22, 2020
    • Yoshaan404
      PastorRay I'm trying to create a support ticket and having trouble. Can you help me?
      • October 22, 2020
    • Yoshaan404
      KyleJohnson Hello Harshaan, Kyle here with Music Tribe. The Deepmind 12 uses a standard IEC connector. You can pickup a power cable at mostly any hardware/computer store or on Amazon.
      • October 22, 2020
  • PenelopeN
    Newcomer - Level 1
    2020-09-05

    Hi I have UM2 and would like to connect it to my speaker which is Portronics Sound Slick II. Please advise how to connect and what type of cables are required for the same. 

    0 92
    • PenelopeN
      ThomasAlexander Hi Penelope, It looks like you should be able to use a to 3.5mm to stereo RCA adapter cable. RCA out to 3.5mm in on the speaker.
      • September 6, 2020
    • PenelopeN
      NicJonesMT Hi Penelope.
      I work in the UK support team.

      Thomas Is correct. If you use a Stereo RCA to TRS 3.5mm jack then you should be able to run the audio from your UM2 to the Sound Slick 2.
      • September 8, 2020
  • Spotlight
    Newcomer - Level 1
    2020-07-23

    Question: Will CAT6 digital snake work with Berhinger WING?

    0 84
    • Spotlight
      Paul_Vannatto Yes, as long as it is shielded and have ethercon ends
      • July 23, 2020
      • Question: Will CAT6 digital snake work with Berhinger WING?
        RoelReynders Does it? It's still AES50, not? AES50 is not compatible with CAT6 as far as I know? But maybe they've updatet the protocol?... So if this is possible with Wing why isn't it possible with X or M32? (I don't wanna snap or point any fingers. I know chats can be misinterpreted. These are genuine questions and I will be gratefull if someone can properly answers those...)
        • July 24, 2020
      • Question: Will CAT6 digital snake work with Berhinger WING?
        Paul_Vannatto Where did you hear that cat6 is not compatible with AES50? I've been using cat6 with my X32 for the past 4 years without any issues whatsoever. In fact one of the events I do every year (except for this year due to the Covid-19) is the finish line for a runathon which requires 700' of speakers through the park from entrance to parking lot. I use a 300' cat6, 250' cat6 and a 100' cat5e between 2 X32 Racks and a couple of SD8.
        • July 24, 2020
      • Question: Will CAT6 digital snake work with Berhinger WING?
        RoelReynders Right! I think it's based on an assumption from a few years back where we had a problem with a connection. It was not the usual CAT5e. We used a local CAT6 and couldn't get the rack connected. I looked up the specs for AES50 and it stated (I realy don't remember where I found the info but I like to backup my information and be reduandant so I must have looked it up on various articles/specs) that it's not compatible with CAT6. I never went back on it and assumed that the info was correct. Now I will test this with our X32 and also with my WIng. I'm sure your right and we probably just had bad luck with that specific CAT6 which would have been faulty. It's not in the habbit of not double checking but at that time we didn't have the time to do this. And based on the info I found I was convinced. So thank you for pointing this out. We 're never to old to learn...
        • July 24, 2020
  • New
    Timrubin
    Newcomer - Level 1
    2020-11-06

    I need to replace the power cord for a Behringer bass v-amp. Power supply model VAMPUL. Please let me know where to order this from. 

    thank u

    Tim R

    0 80
  • New
    robertjm
    Newcomer - Level 1
    2020-12-01

    Hi all,

    Our church has a Behringer x32 soundboard for our sound system. On the back is the x-USB interface, which we connect to a local iMac that's also in the soundpit. At this point I want to repurpose that USB connection to my MacBook Pro, which is up in the balcony recording video. 

    When reading cable reviews on one of the big box sites, I found several where people were saying that the cable I was looking at does NOT support audio transfer. Kind of caught me off-guard, so that's why I'm here.

    I'm hoping for some kind of recommendation for a USB 2.0 USB cable A/B which won't break the bank. One site had cables labeled as "audiophile" and were asking hundreds of dollars, which is just crazy talk. :-) Without measuring my best guess is we're looking at around 20-25 feet in length.

    Since the MBP is fitted with USB-C connectors I realize I'll have to go through an adapter. But, that's the nature of the game with the newest Apple tech these days.

    Thanks!!

    Robert

    read more...
    0 79
    • robertjm
      Paul_Vannatto Hi Robert, I have used a 16' (5M) active USB 2.0 extension cable (similar to this JF-USB-2-0-Active-Extension-Repeater-Cable-Signal-Booster-Extended-Cord - do a search on ebay) with a standard 6' USB cable with the X32 X-USB and X-Live cards (also used it with an MR18) without any issues. That would reach about 22'. Add your USB 2 to USB C converter and it might be enough for your setup. I do see that they also have a 10M (about 32'), but can't confirm if it will work correctly.
      • December 1, 2020
      • USB cable recommendation for X-USB board on Behringer x32 to 2020 MacBook Pro
        robertjm Thanks!!
        • December 1, 2020
  • Siloe7
    Newcomer - Level 1
    2020-10-07

    I am about to purchase the S32 digital snake for our church's X32 console. What is the best Ethernet connection I need to purchase? We will be running it about 100 feet. 

    0 78
    • Siloe7
      Siloe7 I have read that I might need a CAT5e cable but needs to be shielded. Not sure if CAT6 works?
      • October 6, 2020
      • S32 Ethernet cable
        GaryHiggins Cat 5e shielded with ethercons, cat6 shielded with ethercons, or cat7 and cat8 with ethercons all will work. Shielded is a must. (All cat7/8 is shielded). Ethercons also should be used.
        • 1
        • ·
        • October 6, 2020
      • S32 Ethernet cable
        Siloe7 Thank you so much! Helped a lot!
        • October 6, 2020
      • S32 Ethernet cable
        Nigel67 Just as a side note to Gary's comments which are correct, although we have never made any tests or statements with using CAT6, 7 or 8, I would advise that you use stranded core cables and not solid core unless you are installing it behind walls as I have seen to many intermittencies in connections over the years and definitely shielded
        • October 6, 2020
      • S32 Ethernet cable
        Siloe7 Thank you Nigel!
        • October 7, 2020
  • New
    cindysellers
    Newcomer - Level 1
    2020-11-27

    We have acquired two Eurolive B205Ds.  Can I connect them using XLR cable from Thru on the first unit to the Main in on the second one?

    0 75
Go to page