Hey guys,
I have the M Air app on my iPad controlling my MR18. Trying to install the M Air app on a new iPad, I get an error saying that app is gone?! What app is the official Midas MR18 controller app? Are you gonna upload a newer version?
What should I do. I need my M Air app on another device - and I cannot download it....
Also not from previous download (even on the same Apple ID)...
Please help....
Sune
Hi Sune! Ok the M Air App for iPad is up and running again! They had issues with the App and Apple Terms etc, and has been fixed. Search for it under M Air. Seems Tech support gave me incorrect information and has since apologized. However the version is still the same 1.6.5, so not sure if it works on the Newer iPad M1 Chips? Try and see if you can download it.
Hello, i wanted to download the M32 software on my 13" 2020 M1 mac, but it gave the pop up that apple could not check if this software was safe. And that i had to contact the developer and update the software as well.
While my mac and the software i was downloading was the newest available.
MacOS Big Sur and M32-edit 4.3
anyone who knows a solution?
Please comment
Nathan
Hello all! I am new here and am looking for info on the M32 network side of things. I have connected and used our iPad to connect to both our M32 and X32 in the past but have not used it recently due to the pandemic. I pulled everything back out and the X32 worked perfectly, however the M32 was not connecting to my iPad (or vice versa) and so tried connecting via DHCP to see what IP it was pulling. I came to find out that it is pulling a 169.254 IP meaning it is NOT connecting to the router. I then checked the cable - cable works, then tried plugging directly into our unmanaged network switch running to our netowrk closet with managed switch and fierwall - still not getting an IP. Is it possible that my network card is bad?? I am in IT and have had our whole department look it over and so am looking to you guys! Any help would be great! Thank you.
Same here.....M32 has been in case for 6 months, now it will not connect over IP. Next to the plug: the yellow LED works, the green doesn't. Bad signal!!! Router will not connect as before, and in DHCP, nothing happens ( 169.254.xxx.xxx is set, but no comms to the client). With IPCONFIG/ALL command can be seen that the network is doing anything at all. Only one M32 has this issue, the others as well as two WINGs work fine. What is going on??? Anyone else these troubles?
With a few other consoles (A&H, Mackie), a have found that the network transformer had broken connections to the PCB. Replace the dual network transformer > all oK. I checked the transformer in the M32 (built in in RJ45 bus), but all connections are fine. Does the M32 have a 'low level' service mode to check inside operations? I do sorts of this with Digico, a good help in times of system trouble!
Hello all
Does anyone have any insight when a new version for the X&M32 Mix app will come out? Tons of things you can't do on the current app that you could do on the console.
We've been using Mixtender with our Midas ProX and Pro1 for many years and we've noticed that the app will not connect on many of our iPads that have been updated and/or new iPads that have been purchased. Does anyone else have any issues with this? The app also hasn't been updated for years... any plans to update??
I posted some months ago about some minor issues I was having on MS Surface with M-Air-Edit, specifically with "right-click" capability.
I just wanted to give a positive shout-out to the Software Development team. I was fooling around this weekend and downloaded the newest version (as of 11/27/20 I think.) The problems are solved! I have no idea if it was in response to my report, and frankly don't care. It's fixed.
Way to go folks! You continue to impress me!
Just wondering if anyone else has experienced not being able to connect remotely to the console after updating to iOS 14? It works on another iPad that's still running 9.3.5 but it was also working fine on 13 before updating.
console is the Pro 1
Thanks!
My church purchased a Midas 32R board about 4 years ago. About 2 years ago we had a problem and sent it back for repairs. The person that installed it had a spare to load us while it was being repaired. We now have another issue, channels 1 - 8 are dead and we need to send it back for repairs. The company that loaned us one before does not have another one. We would like to purchased an additional Midas 32R to have as a back up while this one is repaired and to have it just in case this happens again. Do you have any Midas 32R mixers in stock?
Thanks, Larry
online editor does not work for mac Big Sur
Someone in our church band recently upgraded their iPad and can no longer connect to the M32 app. It is a 4th gen iPad Pro (12.9 inch) and is running iOS 14.4.2. Putting in the same IP address and linking them on the same WiFi as all of the other devices. Have restarted, redownloaded and repeated everything I know.
Any advice?