Statistics

227,919 members
102,715 posts
  • blastedkane
    Newcomer - Level 1
    2020-07-03
    I am using the following setup x18 mixer with the X-Air app on the Ipad Ipad running Camelot Pro MODX8 Native INstruments A61 Set up 4 port hub plugged into the IPAD A61 and MODX8 plugged into the hub Midi CAble (5 pin) from MODX out to X18 Midi in. Microphone into X18 I have 2 main snapshots 1 - vocal mic is sent to main output 2 - vocal mic is removed from the main mix and re routed to the MODX AD input 1 via Bus 1 which then treats this as the source for a vocoder Camelot Pro is doing a really good job on controlling the programme changes to the modx and also acting as a bridge for the A61 to also control specific channels. Camelot pro also allows for midi programme changes, which I know the x18 can accept. The reason for the request is that i am I do not want the vocoder on all songs, however when not used as a vocoder I need the same mic to act as a standard vocal mic. I could potentially have 2 mics and remove the vocoder source from the mix however the Idea would be to have the single mic covering both jobs and when the song is chosen in camelot pro, the programme change would change to the relevant snapshot./ Can anyone help.
    read more...
    0 46
    • blastedkane
      RexBeckett Midi Program Change 1-64 on channel 1 will load X18 Snapshots 1-64. You need to enable DIN RX on Setup -> Audio/Midi.
      • July 3, 2020
  • New
    Ovnet1
    Newcomer - Level 1
    2021-02-17

    I just bought a td-3 and have spent the last 5 hrs trying to get it to recognize midi via 5 pin din. I have ableton, and don't have any issues using it with the td-3. I have a model cycles as well and the td-3 syncs nicely using the "trig" clock input from the model cycles midi out but will not recognize the 5 pin midi in from the model cycles. I have tried changing every midi setting in the model cycles to send midi. I have changed the the clock input to receive midi on the td-3 and tried using both the same midi channel and different ones on the td-3. It will not recognize midi 5 pin din either from my audio interface via ableton, or via the model cycles. What am I missing, or do I have a defective Td-3?

    read more...
    0 40
    • Ovnet1
      DavidKnighton Hi Ovnet1,
      Are you using the SynthTribe tool with TD3 to change these settings? As far as I know, that is the only way to change between using MIDI Din and the patch I/O.
      • Feb 17
      • Behringer TD-3, Elektron model cycles sync
        Ovnet1 Yes, I have the SynthTribe tool and have used both it, and the manual way to switch between clock sources and PPQN. I'm at a loss honestly. I'm going to test it with a couple other pieces of gear to see if I can get it to recognize the Midi, if that doesn't work I suppose I'm going to chalk it up as defective and send it back and get a new one, unless someone comes up with something I haven't tried.
        • Feb 17
  • New
    stormfield
    Newcomer - Level 1
    2021-03-01

    Hi! Can anyone advise? My TD3 resonance knob needs replacing, it's out of warranty.

    Does anybody know what part nunber it is, or where i can find it? The potentiometer

    When turning quickly, it makes a loud crackling sound. Less bad if turned very slowly. A spray of contact cleaner helps fix the problem for about 15 minutes, then the crackle returns. 

     

    Thanks in advance!

    read more...
    0 31
    • stormfield
      DavidKnighton Hello stormfield,
      it sounds like your potentiometer could use a lubricant instead of cleaner. Some cleaners claim to lubricate as well, but don't believe the hype. At any rate, you will need to submit a SPARE PARTS request to see if you can order the correct pot. The part number is I03-00002-21350. It is a mono 50 K-Ohm B taper. Click the SUPPORT tab at the top of the page, then scroll down and click the SPARE PARTS tile to submit a request. We have 200 pieces available currently in USA.
      • Mar 2
    • stormfield
      stormfield Hi Dave, thanks for the quick reply. re: the potentiometer lubricant - what brand/name of spray would you recommend for this? I could try that before going the component route
      • Mar 2
  • New
    Chimpfinga1983
    Newcomer - Level 1
    2021-02-02

    Any idea exactly what I need to do in order to set these up ? 

    been trying for a week now and it's still not working properly. 

    the force should usually sync midi devises but it's only synced with the sequencer and not the oscillation or the envelope. 

    I'm a newbie to setting up midi equipment. M

     thanks 

    read more...
    0 26
  • New
    DagobertoPatlan
    Newcomer - Level 1
    2021-02-08
     

    I just picked up a Behringer Wasp and I'm having an issue- It does not see every midi command - just every other.  At first I thought it was my keyboard so I connected it to my VJ-1080 and it works fine. I did wait the 10 minutes for it to warm up before I started using it. When I look at the MIDI light- it changes color when I send the first key but does NOT change color when I send the second.  However, when I send the same MIDI commands to my Roland, the MIDI light sees every key stroke.  Any thoughts?

     

    According to the software, the unit is up to date.

    The company I bought it from asked me to reach out to MusicTribe before returning it. 

     
    read more...
    0 21
    • DagobertoPatlan
      NicJonesMT Hi Dagoberto.
      Could you please submit a technical support ticket by pressing Support at the top of the page.
      We can then go through some trouble shooting with you.
      • Feb 9
      • Wasp skips every other trigger
        DagobertoPatlan I did this morning. Thank you!
        • Feb 9
  • New
    fusseltier
    Newcomer - Level 1
    2021-04-08

    I've registered twice and still haven't received my tracktion activation code. 

    0 16
  • New
    fusseltier
    Newcomer - Level 1
    2021-04-12

    Still haven't received my tracktion activation code yet. My tickets keep being closed but nobody contacts me or sends my code. 

    1 12
    • fusseltier
      KyleJohnson Hello, if you can please send me a message with one of your case numbers I will look into this issue for you.
      • Apr 12
Go to page