The Behringer Xenyx 302 USB Mixer only supplies 15V instead of 48V of phantom power. Would that be enough to power the Mic Booster CT1?
Hello Brian, welcome to the community.
According to the specifications, the CT1 requires 48V phantom power. You could use an external phantom power supply between the CT1 and the mixer.
You would need a device such as the Behringer PS400
Ok, using the Behringer PS400 I would insert into the mixer using a 6.3 jack and not the xlr in order to bypass the automaticly provided 15v phantom, correct? Or it doesn't matter?
I have a DM8000 that I can not connect to, is there a way to either find the ip address or do a factory reset.
Hi everyone,
I recently purchased the 76-kt compressor and im absolutely loving it. I am aware of the rear vu meter adjustment pot as stated in the start up guide but there is also a small hidden screw directly underneath the vu meter that i have messed around with (which i regret doing) i dont know why i messed with it, i was just curious what it did.
Im worried ive somehow messed up the calibration now as i presume this screw is factory set and shouldnt be altered. I can see that you can turn it clockwise and anticlockwise one turn and then it becomes stiff, you then screw further past that stiffness and it sort of resets to the loose, clockwise/anticlockwise setting as before.
Am i ruining the screw by turning it over and over to see what it does? is it some sort of spring that i am unwinding?
Id really appreciate any technical information to settle my mind on how this screw works and what you should do with, if i have perhaps ruined it by over turning it, or if i am just worrying too much?
Thanks ever so much in advance.
Hello. first post here from the USA thanks in advance for any help.
Just got this used 360 and thou it passes audio with no issue both A & B EQ has no effect on said signal.
On a side note, I'd like to know what these 2 holes on the back marked "In put TX and Out put TX" are for. Is that a switch inside the unit (I see something white in there but not sure what it is)? Is that why I'm not getting anything more than by-passed signal?
Seiral #36514
Hopfully some one will know what the trouble is and leave a reply, I don't like flipping switch's on (or off) with out knowing what they do.
Hi,
Have tested using the CP8000 but as it doesn't use a rotary encoder, it will not work safely for mixing volumes. Due to the volume jumping to the position on the volume know when you change buttons.
Is there a way to include a rotary encoder in system? or would I have to go to rs232?
Thanks,
Stephen
Hi Stephen
If you want to add an encoder to provide volume control over up to 8 seperate input or output levels, you can use the new KT DM TCE.
Hello
was wondering how to get this option and how mutch it cost ?
Greetings! I have largely complete my initial design for a DM8500, made it look good, etc. When I went to compile it though, it listed several apparently unplugged modules that I can't find anywhere on the design. Maybe they are hiding behing a different module, but I can't find them. Is there a way to list all of the used modules with their associated ID numbers to facilitate in the troubleshooting process?
Specifically, the compiler says that High Pass 6-24 dB/OCt (ID=8) is not an input module, and that the same filter ID=11 has no input or output (none of the High pass filters that I can see in my design are ID=8 or 11). Also, modules 12-16 have the same issue. They include 2 Parametric EQs, 2 comp/Limiters, and another high pass filter.
It is possible that I created some modules early in the process before I knew what I was doing and then deleted them (or at least I THOUGHT I deleted them!). But if I can't find them and make them go away, I can't complie the design, and the machine is useless.
I attached a picture of my design. i would be happy to email the actual .dmd file, but apparently that can't be attached to the forum.
Hi, I need to aquire some rotary encoders for my DN 8000.
Please let me know where I can purchase these in the UK.
Many thanks.
Steve.
I am interested in building a abelton live backing tracks rig,I have a Midas pro1 console in which I want to use as my board for virtual Sound check but also want the ability to use for mixing backing tracks for live performances, so any suggestions in which klark teknik dn9652 or dn9650 also using the kt-usb network card for multitracks, thank's
Thanks probably go the dn9652 route and buy the aes 50 card and the kt-usb 2.0 card