Hi, can I use the Klark Teknik DN9652 to convert a Dante signal into an AES50 signal?
Currently, I am hoping to replace our Behringer X32 board with a Yamaha TF5. Unfortunately, our X32 is connected to a Klark Teknik Dm8000 DSP which has an AES50 card, and the DSP is locked with a password. We wish that we could convert a Dante signal into an AES50 signal so that we won't have to mess with the DSP programming. Is this possible?
Thanks.
Hello,
I have seen recently that the LA-2A type compressor initially called KT-2A is now named 2A-KT?
The team in question do not have a presence on Community, can I ask you send your inquiry via the above support tab/pre-sales many thanks
Kdx 15
Hi folks.
Is the KT-2A going to be available again? I'm keen to have one, but if not I will look at other options. Thanks.
The Behringer QX mixers are equipped with a multi fx processor made by Klark Teknik.
I would love to see a standalone device using this processor. Maybe a small one similar to the TC M100 or even in a 19" housing with, lets say, two or four of that processors and the possibility to tweak more parameters for each effect, a tap tempo button, and so on. Something may be similar to the MX400 made by Lexicon but with all that phenomenal suberb effects of the Klark Teknik processors.
I would buy both,the small one and the larger one,even if I own a M32, a X32, a WING (among others) and some vintage effects made by some well known manufacturers.
the components are already available,so put it in a box and ship it.
kind Regards
Klaus
Hey, is there a way to aggregate the Dn9630 with another interface to use the outs of the interface to send to another destination other than the mixer (X32)?
I am HOPING to use the DM8500 as the brains of my entire installation. Part of that requires being able to use TCEs to send signals to the GPIO outputs… but I can’t for the LIFE of me figure out how to get ANYTHING to talk to the GPIOs or generate logic inputs of any kind)! I would LIKE to have buttons on the TCEs be able to trigger various GPIO pins hot or cold (as well as other logic within the system), but I have not found a way to do that AT ALL. To me that seems like a pretty basic function (that apparently was available on the previous wall controllers), but I can NOT find it.
I have one GPIO input (or any logic input) signal that is critical to the audio design, and I need to trigger 4 GPIO pins which will be used to control various presets on a digital SDI switcher (to include choosing which HDMI inputs will send the audio to the DM-8500 given various settings).
Is there a Logic input setting that I can trigger from a DMTCE? Unfortunately, due to a lack of great documentation, I chose this system with the assumtion that this would be a given, but now that the entire system depends upon it, I am finally able to figure out that it might not work. I am really hoping for a simple solution I just don't know about yet!
HELP?!?!?!?
I have a KT-2A which I use for recording and compression of bass guitar or electric guitar, and for singing ofcourse. The way I do this is:
- for the bass and guitar via a mic in front of the cabinet, and singing via a voice mic
- input that into a voice preamp, in this case a Tascam TA-1VP
- output that to the KT-2A
and in that case the KT-2A works fine, the meter responds as an indication that the signal is processed.
HOWEVER, what I also want is to add the KT-2A to the effects loop of my guitar amp, and this is what does not work:
- send the preamp signal of my guitar amp (Marshall JVM or Fender tube amp) to a DI box input
- connect the XLR output of the passive DI box to the microphone input of the TACAM TA-1VP
- output that to the KT-2A and connect the KT-2A output to the return of the effects loop of the guitar amp
In that case the meter of the KT-2A does not respond no matter how I set the peak reduction knob: the meter stays on zero.
I suspect the output of the SEND of the guitar amp is too different from the microphone output, even it I have a DI box in between. So how can I get the KT-2A to work in an effects loop of a guitar amp?
HI All
I search an update firmware for DM 8500
Someone can help me ?
Thanks
Thanks a lot NicJonesMT !!