Statistics

294,136 members
177,206 posts
  • New
    nektarios303
    Newcomer - Level 1
    2021-10-19

    Hi,

    I own a pair of KT-2As (and 76-KTs) and wanted to ask two questions.

     

    1) Upon using stereo link and calibrating the two units with a 1khz test tone, using the Stereo Link trimmer at the back to get the same amount of gain reduction, I get different amounts of gain reduction between the two units when I move the Peak Reduction. The test tone is a mono signal sent to two outputs of my soundcard. No faders hhave been touched in my soundcard's mixer, the stereo output pair I am using on my soundcard, shows the same signal between the two outputs I am using for Left and Right that are the inputs to the KT-2As.

    So I am using them unlinked which is fine, but the bottom unit in the photo, needs to have the Peak Reduction pot much more CW than then top unit to show the same amount of gain reduction. How do I go about calibrating the unit so that it behaves like the top one?

     

    2) My units are running hot. I can put my hand on them, but they are very hot.

     

    Do other KT-2A owners experience these two behaviiours I am?

     

    Cheers!

    read more...
    0 38
  • New
    Joinville
    Newcomer - Level 2
    2021-09-01

    Good day,

    Any idea on how to send audio of DM8000 USB to A computer (50 mtrs)?

    0 37
  • New
    husnain9
    Newcomer - Level 1
    2021-11-24

    Hello Team,

    This is Husnain from Pakistan and i have 100 audio processors Model: DMA-8500 each piece is for each classroom of different universities. Can anyone please help to suggest how can i use all input channels as i have 8 mics in each classroom. 

    Senerio is like i have 2 speakers which are connected with amplifier 2 seperate channel. Microphones connected with Digital Audio Processor work with first 2 channels but other channels are not working as it has to be configured. I would appreciate if anyone can share configuration mannual so all 100 devices can be configured accordingly. Thanks

    regards,

    Husnain 

    Email: [email protected]

    read more...
    0 23
  • New
    mblackuk
    Newcomer - Level 1
    2021-09-29

    Hi guys,

     

    My DN6000 has suddenly gone darker on the left side and a message saying "low battery" appeared. 

     

    I changed the battery (2430) and there is no low battery message any more but the screen is still dark on one side.

     

    I'm attaching a pic, can anyone shed a light as to what's happening? (excuse the pun) Thank you.

    read more...
    1 23
    • mblackuk
      WilliamR Hello, William from musictribe here. Please click on the support link above and create a support ticket and an agent will contact you ASAP to help you out.
      • September 29, 2021
  • New
    mheroux
    Newcomer - Level 1
    2021-12-28

    Hi, 

    I managed to grab a DN3600. I added it to my guitar rig. It does a worderfull job :)

    However I cannot manage to add it to my midi setup. I use a Roland midi as HUB and use a 5pin to 3pin cable to connect the EQ to the HUB.

    The manual is not clear if it respond to regular midi message as a standalone device or if it require a specific setup (as of the master/slave section). I tried the omnichannel and different channel setups... it doesn't respond to any messages.

    Anyone have any idea ? 

    Thanks

    read more...
    0 18
    • mheroux
      Dale_M Many thanks for your post, the midi is not used outside of the DN3600 world, please see the statement from the user manual.
      • December 28, 2021
  • New
    JeffreyBridges
    Contributor - Level 2
    2021-12-17

    My DN9650 with USB card was working fine with my Mac and Pro1 until I moved it. It is kept in a rack with 2 DL153 stageboxes. Once it was hooked up in the new location, it does not recognize AES50 connection. After checking and swapping cables around I determined that the cable is not my problem.

    The led just flickers on the back of the unit and the Pro1 does not recognize it as connected.

    I am hoping for someone to give me some pointers for troubleshooting this issue. 
    The DN 9650 has never toured. In fact it has only been moved one time. It is very pampered

    read more...
    0 17
    • JeffreyBridges
      JeffreyBridges I am proud to admit that the problem was me! I had plugged the Duracat into the “Control” port and NOT the #1 aes50 port.
      All is fine
      • December 19, 2021
  • New
    albucristian83
    Newcomer - Level 1
    2021-11-25

    Hello,

    Reading the product manual for the KT-2A leveling amplifier, found this written:

    "The controls on the 2A-KT consist of a Pre-Emphasis trimmer which adjusts the compressor / sidechain interaction. When set fully clockwise, the sidechain responds to the full frequency bandwidth of the incoming audio. As the trimmer is turned counterclockwise, the compressor responds less to the signal's high frequency transients."

    Shoudnt be the opposite for counterclockwise rotation? Meaning the compressor reacts more to high frequency acting like sort of a de-esser?

    Why to react more on the lows and ignore highs?

    I ask this because this is the functionality I know the older LA2A units have...

    Many thanks for reply and clarification.

    BR,
    Cristian

    read more...
    0 17
  • New
    elove1918
    Newcomer - Level 1
    2022-02-08

    Can i plug my dl 32 directly to dn9630 and then to my  DAW over usb and use the dl32 and the dn9630 like and interface

    0 14
  • New
    Davpis
    Newcomer - Level 1
    2021-11-23

    When will these be available again? I've been waiting over a year with Sweetwater it's backordered

     

    thanks

    0 14
  • New
    kountrykid
    Newcomer - Level 1
    2021-11-04

    Hello,

    As mentioned in the subject line, I'm trying to connect the brackets that came with my Klark Teknik DW20BR, so it can be mounted.  Though, the screws provided are too long after removing the black rubber feet that are originally mounted.  And, it doesn’t come with any shorter screws. Trying to figure out what I’m missing here? Thinking maybe I’m missing a step.

     

    Tony

    702-523-0126

    read more...
    0 14
    • kountrykid
      Nigel67 Hi kountrykid. It appears that you are doing everything correctly. The screws that you take out to remove the rubber feet should then screw straight back in. They screw back into an extruded aluminium case which should have threads made into it long enough for the screws to be tightened into. There is no pcb, etc in the way that they can be fouling on. The screws should be 15mm long. Can you confirm that they are this long? Either they are too long in the first place or the aluminium extrusion has not been threaded deep enough. I don't want you to force it, but can you try putting a little extra pressure on one of the screws to see if it tightens up any further. If not, then I would advise contacting the partner that you purchased the unit from and asking them for a replacement unit, making sure that they check the replacement unit so the screws do go all the way in when the rubber feet are removed. Have you checked all 8 screws? Many thanks
      • November 5, 2021
Go to page