Statistics

261,398 members
140,116 posts
  • New
    JusRoc1
    Newcomer - Level 1
    2021-12-02

    hello

    was wondering if the x touch could be reset

    to factory condition

     

    have my second brand new x touch and it has started to malfunction as well

    very angry at that this isn't working

     

    i am running good hardware on pc (i7/16GB Ram) and audio card (UAD)

    read more...
    0 1
    • JusRoc1
      RobbyWingfield Hi this is Robby with Music Tribe. Please submit a Support ticket at the link support link above. There is no factory reset on the X-Touch as the settings of the controls on the X-Touch are hard wired and only vary depending on the mode you choose. In your support ticket, please describe in detail the issue you are having. Make sure to include what DAW you are using. Thanks!
      • Dec 4
  • New
    CourtneyJ_Dotha
    Contributor - Level 2
    2021-12-01

    We use the X32 rack for a closed in ear monitoring system and now I need more inputs and monitor sends (S32).  Right now I have a 16 channel split snake (tails) that go to FOH.  Can the FOH send be done with cat5 now?   Will the X32 cat5 send be compatible with other brands?  I want to avoid gettin 2 more splinter (S8s) and more cables.  

    read more...
    0 0
  • New
    BeatleManiac
    Newcomer - Level 1
    2021-12-01

    Can someone from Behringer reach out to me on ticket CAS-504194-G3T2K3?  I see that it was closed yesterday and no one has contacted me.  It needs to be reopened.  I need a part number for the frequency sweep pot (6-pin, no detent) because it doesn't work on 1 channel of my Behringer PMP6000 powered console.

    I have attached the section of the schematic with the needed pot highlighted.  It is a 500KC pot.

     

    Thanks,


    View Attachment
    read more...
    0 7
    • BeatleManiac
      Nigel67 Hi BeatleManiac. I see that you submitted two tickets for information for the same part. The Spares Team have closed one and are corresponding with you on the other case (CAS-504413-D6M3W4). I am sure they will be getting back to you Monday or Tuesday with regards to the last question you have sent them. Many thanks
      • Dec 3
  • New
    OttovanZanten
    Contributor - Level 1
    2021-12-01

    I made a short video to explain what's going on

    When I use Oscilator 3 (or the LFO) to modulate the filter at Audio Rates I can hear the oscillator through the output, even if I switch it off in the Mixer section.

    By the way the LFO does the exact same thing. I forgot to demonstrate, but if I change the modulation source to the LFO and turn it up into audio rate you can hear it, it's just a lower pitch because it's not as fast as Osc3.

    I would expect the oscillator to be silent, but I can hear it even when I close the filter and turn down resonance entirely. This is desired behavior. If it's a faulty unit I will return it, but if it's just a limitation/quirk of an older synthesizer design I will live with it. It's not like I use audio rate filter modulation in 95% of patches, but I do love me a vowely formant synth sound.

     

    I'd love to hear what you think. Let me know if this is not enough info to recreate it and you want a patchsheet.

    read more...
    0 10
  • New
    francescotesi
    Newcomer - Level 1
    2021-12-01

    Hi,

    I experienced a noise on the upper part of the HPF fader on ODYSSEY. This noise is stronger in some configurations of the synth chain. What can it depend on?

    read more...
    0 2
  • New
    Attori
    Newcomer - Level 1
    2021-12-01

    i came to this site to register a Pre amp. So how do i do that ? 

    1 8
  • New
    KristianLCarpenter
    Newcomer - Level 1
    2021-12-01

    I unhooked my xair 18 to move it. Now, my devices are not recognizing the xair wifi. It is set to wifi client access point. But, there is no led light on indicating the wifi is on. I believe there is supposed to be an led light on. thank you

    0 0
  • New
    DavidSelf
    Contributor - Level 2
    2021-12-01

    Is it possible to plug a midi controller into the midi in port and pass notes to my PC for driving a virtual instrument?  Reading the manual implies that midi is only used for remote control and internal functions.

    0 4
  • New
    jeromem
    Newcomer - Level 1
    2021-12-01

    Hi,

    I’m not sure about how correctly using my UMC204HD interface with my my electric guitar (passive pickups).

    Of course, i’ve plugged it in through the usual 6,3 jack and I set the Inst mode.

    But I noticed when I don’t use the pad button, the guitar signal is so high that I need to set the gain to 0. And even so, the signal gets clipped. Is it supposed to behave that way with an electric guitar with passive pickups?

    So, it seems the only way for me is to use the pad button with a 50% gain. I’m suprised so. 

    Regards,

    read more...
    0 6
  • New
    jblair
    Newcomer - Level 1
    2021-12-01

    Re: Case CAS-466240-T5N7P2

    I sent in a Tannoy Gold 8 studio monitor to be repaired since it was still under warranty.  I sent the speaker into the repair center on June 29 and I received notification that it arrived on July 14.  The only communication I have gotten since then was on September 13 which stated:

    Your unit has been evaluated and parts have been ordered. We currently do not have the parts in stock and they have been placed on back order. I do not have an ETA at this time.

    Is there a reason that a repair should take this long? Why not just send a replacement since the monitor was still under warranty?

    I would appreciate some clarification and some action since having one expensive monitor sitting in my studio does me little good.

    Thank You

    Jeffrey

     

    read more...
    0 10
    • jblair
      Nigel67 Hi jblair. I can only apologise for the delay in repairing your loudspeaker. I have checked your ticket and messaged the colleague who is handling it and asked him to contact you with the present repair situation on Monday. Again, I am very sorry for the inconvenience this is causing you.
      • Dec 3
Go to page