305,340 members
189,622 posts
  • New
    Newcomer - Level 1


    I really like the flexibility of the unit, to be used as an interface (for recording to DAWs) or as a small mixer (for live performances and streaming). Can you please consider these new enhancements/functionalities for the next firmware/app update. These requests are more from a small mixer perspective (enhancing the workflow on the fly for live performances). I have included screen shot illustrations that describe the high-level asks and requirements.

    1- For the channel settings screen, allow the user to switch between different channels. Eliminating the need to page-out of the screen and go back to the Mixer screen (in order to select a new channel).

    2- For the 4-Band EQ screen (when in Full Range mode), allow the user to also be able to type in a specific frequency (for quicker accurate selection of a frequency).


    3- For the Preferences screen, add the ability to SHOW EFFECTS & MONITORS FADERS (DCA) on the Mixer screen. These faders will display on the Mixer screen and control the levels of FX1/FX2 (linked), and MON1/MON2 (linked) in the overall mix.


    4- For the new EFFECTS & MONITOR FADERS (on the Mixer screen), allow the user to click inside these new faders to open up a new EFFECTS & MONITORS screen (for a quick view of the underlying FX1, FX2, MON1, MON2 levels). Also include MUTE buttons for all faders (for existing and new screens).


    5- Please add a similar "one-knob" gate, to compliment the one-knob compressor (at least on the first 2 mic channels)

    6- Add ability to setup a quick Mix-Minus would be great (I see many folks have requested Mix-Minus)

    Great product for what it is.




    0 3
  • New
    Newcomer - Level 1

    I have a Konnekt 6 its firmware ver 1.02 
    i need the firmware ver 2 or last firmware

    Where can the firmware for desktop Konnekt 6 be downloaded from?

    please help me

    0 11
    • khongkhiem22
      khongkhiem22 please give me firmware
      • May 10
    • khongkhiem22
      khongkhiem22 I logged into website and installed Driver version 3.6.1 for Windows already. However, Firmware version is still 1.02 build 1995. So, I wanted to upgrade to Firmware 2.02 build 2221 or last firmware     (this version has much better sound quality). Thank you.
      • May 11
    • khongkhiem22
      Nigel67 Hi, please try this link Select Desktop 6 in the Product Tab, Software in the Type and then tick the box labelled Show All Versions.
      • May 11
  • New
    Newcomer - Level 1

    Submitted a ticket on 5/1/22. Within 2 days the ticket status showed problem solved. Where do I find the solution? Never received an email or link.

    0 40
    • mac33
      NicJonesMT Hi Mac33
      Can you please check your email settings. 2 emails were attempted to be sent to you however they were rejected by your Email client.
      Can you please ensure that [email protected] is not blocked.
      Once you have changed this, let me know and I will ask the team to resend the last email.
      • May 9
      • Problem solved??
        mac33 If they resent the email, I am still not receiving it.
        • May 10
    • mac33

      Thanks for quick response. Double checked and [email protected] is not blocked. I added to safe senders also.

      • May 9
    • mac33
      mac33 If they resent the email, I am still not receiving it.
      • May 10
    • mac33

      Today I finally received 5 email responses with the same links. All 5 brought me right back to this conversation. Nothing found from Nigel as indicated.

      • May 12
  • New
    Newcomer - Level 1

    Hello guys.

    I have the Behringer U-Phoria UMC204HD and obviously I'm a newbie in advanced sound technology.

    I bought the interface with the idea, I have two seperated recording devices in Windows.

    Now I understood, that I only have "In 1-2" as a recording device and Input 1 is on the left channel and Input 2 is on the right channel.

    Is it possible to split this recording device into two seperated recording devices like "In 1" and "In 2"?

    I also heard of the ASIO technology in some programs. They can seperately use the channels, but my programs don't use that and can only detect Input 1 / the left channel.

    Already tried to use different driver software from

    Googled a lot, but did not find a solution yet. Do you have any idea?

    Thank you in advance! ^^

    0 32
    • P4SCVL
      Nigel67 When you registered your UMC204HD within 90 days, you would have received a free license to download Traktion or you can download Audacity free of charge and even though you set up the UMC in the preferences as stereo, you can still record to 2 mono tracks, so you get Input 1 to the first track and input 2 to the second track
      • Jan 29
  • New
    Newcomer - Level 1
    • Nadia40
      Nigel67 Hi Nadia40. You will require the serial number of the headphones to be able to register them. They will be on a label on the headphones. The serial number begins with a S and ends in 189. Without this, it is not possible to register them. Once you have all the details, please fill in the Product Registration form. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Product Registration tab and submit your registration ticket. Many thanks
      • November 16, 2021
  • New
    Newcomer - Level 1

    Been banging my head on my desk TRYING to get this to work.
    I gave up :-(
    I am now reaching out to you . . .

    Here is what I am trying to do.

    Play music on the internet Using my mixer

    Control volume of music
    Control volume of XLR Microphone
    Kinda like a radio station, 

    we hear the DJ talking....he plays music....he talks as the music is playing

    The Music is coming from my PC
    I do not want to hold a microphone near a speaker, that would sound horrible. 

    Gosh is hard for me to express what I am trying to do,  but hope you understand.

    0 63
  • New
    Newcomer - Level 1

    Problem : I don't appear to be able to record a full 'waveform'. Recordings are clipping much earlier than it should when using the Behringer Audio interface

    info: I have an Audio Tehnica 2020 mic going into a U-Phoria UMC204HD going straight into my PC via USB, and into Audacity.


    When I was recording my waveforms weren't that large (or loud). I therefore decided to see what the maximum levels i could record to see how much headroom i was able to play with

    Test1 - Mic levels at 100% on the Behringer: PC record level at 100%, shouting into mic (maxed out/ hot/distortion to be expected)

    Result: Clipping and distortion occours at the 50% mark on the waveform - Image 1

    This makes me wonder my clipping wasn't happening at a much louder level? Should it not clip when the waveform is fatter/louder

    This makes me wonder why when I record normally, things are quiet. I don't appear to have the full headroom to play with. as clipping happens much sooner than expected.


    Test2 - used my BOSE headphone microphone, NOT going through the Uphoria, straight into Audacity - image 2

    Here I seem to have a much bigger dynamic range as the waveform is fatter and almost to the full.

    As this test was not going through my Behringer I am wondering if that is the problem


    The Behringer is only a couple of months old, and hardly used. Could anyone give me some ideas for further testing? or options, or could the Behringer be faulty


    0 582
    • kuztardd
      RexBeckett Hi kuztardd, the recording level in the UMC204HD driver may be set to less than 100% so the signal is being attenuated. You can adjust this through Windows Control Panel -> Sound -> Recording -> UMC204HD -> Properties -> Levels.

      You can also adjust the same level control through Audacity as long as the UMC204HD is selected as recording input. See attached screenshot. If you do not see the recording and playback faders, open View -> Toolbars and enable Mixer Toolbar.
      • June 22, 2021
    • kuztardd
      kuztardd HI rex thanks for taking the time to reply.
      MY settings there (and on the slider on Audacity are set to 100. So feel like the its Audio interface is limiting my output by 0.6db as my audacity records my bluetooth bose fully and that doesnt go via the Behringer?
      do you have any suggestions of any testing i can do before i think about doing a warranty swap with Behringer should i consider it faulty?
      • June 23, 2021
      • Why does my Behringer output at a quiet level?
        RexBeckett I know that the UMC204HD normally can output a full-scale USB recording level. If you want to be sure that your unit is defective, you could test with different sources and another PC. I have found that some issues are solved by disabling all enhancements on the Advanced or Enhancement tabs of the device properties.

        Other than that, I suggest a warranty return to either your supplier (if purchased less than 30 days ago) or through the Support menu at the top of this screen.
        • June 23, 2021
    • kuztardd

      Hey I found the fault! I installed my Behringer on another pc along with Audacity and noted that on the fresh PC that I could get full waveforms. The only difference I noted was that my pc 'Audio Host' was set to the default of MMC
      and the other pc was set to WINDOWS WASAPI

      It explains why the sound has always sounded pretty cack too. You can hear the difference here:

      • July 7, 2021
  • New
    Newcomer - Level 1

    Hey fam,

    I attempted and successfully replaced the battery on my System 6000 MK1/Black. I actually installed an "Upright 3-Tab" CR2032 battery holder that I can pop a new battery in and out of! It worked great and I was able to get my licenses back within an hour of the new battery and holder install and I ws back up and running. I attached a photo of the holder. I actually purchased them on Amazon. I had to purchase a dozen but were less than $7 US. 




    0 71
    • guitar012001
      Nigel67 Many thanks for sharing. I have never seen a vertical holder like that before. That will come in useful for some old Klark Teknik products.
      • February 8, 2021
      • Attempted Battery Replacement on my System 6000 MKI
        guitar012001 You’re welcome Nigel67! Here’s the holder I ordered!
        • 1
        • ·
        • February 9, 2021
  • New
    Newcomer - Level 1

    When integrating Behringer Wing into Cakewalk my DAW only reads MME devices. When switching to ASIO my DAW is able to see all the channels that I need (32), Tho I am not able to select ANY of them as devices for use. As of now cakewalk only allows up to 8 channels left right and stereo under MME devices...

    I have provided a screenshot of what I am looking at when it comes to having my DAW pick up the asio channels 1-32 tho I am not albe to select or activate them with a checkbox. Everthing else runs smooth as butter when my driver setting is set to MME devices, tho I am limited to 8 channels basically...

    Is there a workaround for this or is this a compatability issue with Cakewalk and the Wing?

    0 152
    • lbsmith
      DavidKnighton Hello ibsmith,
      From what I understand, ASIO4ALL is supposed to allow aggregate devices, however the WING does not utilize ASIO4ALL, and instead has it's own dedicated ASIO driver.
      • February 3, 2021
  • New
    Newcomer - Level 1

    Have a problem with notifications popping up of my Midas DL251 loosening communication.

    There is two New cat6e shielded with shielded ends an ground soldered to the clip

    225 ft of cable.

    replaced all last week but came in this morning for service an still have the same problem. 

    0 324
    • Shanog5050
      Nigel67 Hi Shannon, please can you click on the support tab at the top of the page and on the new page that opens submit a Technical support ticket. We will need to know whether you are connected to the surface AES50 ports, or DN9680's. We do only specify that CAT5e should be used, however CAT6e shouldn't make a difference. Have you tried different AES50 ports and the HD96, and also check for bent pins in the AES50 ethercons on the DL251 and HD96. Is the DL251 running HD software, what settings do you have on the front panel of the DL251. If you could include all this information on the ticket then we will be able to help you further. Are the dropouts happening frequently or just this one time? I would also suggest trying different cables as well for test purposes. Many thanks
      • January 3, 2021
Go to page