Statistics

305,438 members
189,736 posts
  • New
    OliverATX
    Newcomer - Level 1
    2022-08-24

    Hello All!

    I hope everyone is doing great!

    In setting up my X32 (still very new to it) I came across an issue I would appreciate some help on.

    Scenario is as follows:

    Bass cabinet with 1/4 TRS OUT is going into DI BOX. DI BOX with 1/4 TRS OUT is going into X32 1/4 TRS AUX IN port 2.

    I have setup X32 routing as follows:

    #1) USER IN: Mapping Aux In 1-6 to Inputs 17-22 (screenshot 1)
    #2) INPUTS: Channel 17-24 > User In (17-24) (screenshot 2)

    My question is around #2. For the last gig I had NOT selected User In (17-24), but left it at the default, which was just AES50-A 1-8, I believe. Everything worked fine and I adjusted levels, EQ, etc. in the AUX FX section (screenshot 3). When looking at the mixer channels 1-32 view, there was no signal registered at Input 18, I only saw the signal in the AUX FX section on Aux 2 (as expected based on the routing selection in #1.

    After selecting User In (17-24) in #2 I now can see the bass signal register in the 1-32 mixer view on Ch 18 (screenshot 4).

    Questions:

    A) Is this the correct way to do AUX routing at all?
    B) If #2 is selected, I now have the option to change MIC pre input sensitivity (or EQ) either in the AUX section (Aux 2) or in the 1-32 mixer view on CH 18, or both. What is the recommended way?

    Thank you!

    Oliver

     

    Screenshot 1)

    Screenshot 2)



    Screenshot 3)



    Screenshot 4)

    read more...
    0 17
  • New
    saifzack
    Newcomer - Level 1
    2022-08-24

    Hi everyone, as a beginner I just bought 1 set of Behringer Europort PPA500BT, so may I ask where should i get a Effect Table as guide to use Klark Teknik Multi-FX Processor preset?

    Sorry for asking, because I can’t find anywhere.

    Here i'm attached pic as example.

    Thank you very much for any help.

    read more...
    0 22
    • saifzack
      Dale_M Thank you for your inquiry, I have checked the QSG documentation and it appears to have been missed, I will see if this can be corrected.
      • Aug 23
    • saifzack
      saifzack Thank you for your respon..so where should i get the effect table
      • Aug 27
  • New
    Edu1980ardo
    Newcomer - Level 1
    2022-08-16

    Alguém já teve um problema semelhante e poderia me dar apenas uma direção por onde iniciar testes?

    0 9
    • Edu1980ardo
      WilliamR Hello, William from musictribe here. Please check the buy link on the product page. There is a service center link with all of the available authorized service centers.
      • Aug 16
      • Pedal de efeito V-AMP  LX1-X
      • Pedal de efeito V-AMP  LX1-X
        Edu1980ardo Na verdade eu não tenho intenção de enviar meu equipamento para uma autorizada...pretendo fazer o serviço eu mesmo...só imaginei que este modo como os leds estão acesos fosse um erro padrão pois já vi no YouTube alguém com este mesmo defeito porém o vídeo apresenta apenas esta falha...e como para dar um reset é indicado pressionar duas teclas específicas e ligar a fonte de alimentação do equipamento, imaginei que houvesse um padrão para reverter este problema também...mas agradeço pela boa vontade?
        • Sep 9
  • New
    dorinh60
    Newcomer - Level 1
    2022-08-14

    Hello, I purchased the UCA202 interface FEW months ago. I used it for playing my digital music on my stereo system and it worked very well. I tried to convert some music from vinyl records using the input jacks but Audacity keeps reporting an error. I also noticed that the driver installation is done in the (x86) folder even though I have an x64 system and in the Device Manager it appears as the standard USB audio codec (Audio Endpoint) provided by Microsoft. Even if I use my laptop to listen to vinyls in its speakers it doesn't work.
    So what could I do in this case?

    read more...
    0 24
    • dorinh60
      dorinh60 Nobody? Something, anything...?
      • Aug 17
    • dorinh60
      Paul_Vannatto Windows can only work with one soundcard at a time. The UCA202 via SB is a soundcard. If you select it for the inputs, the outputs will go to the UCA202. That's the limitations of Windoze (spelled intentionally). If you want more versatility, switch to linux. I did that when they abandoned Win7 and glad I did.
      • Aug 17
  • New
    dwdata2000
    Newcomer - Level 2
    2022-08-12
    I am using a remote control called "Mixing Station" to control my Behringer XR18.

    The app allow you to define your own UI to your taste. I have 3 buttons on my MAIN UI that trigger Mute Groups 1-3.
    when they are selected, they illuminate to a brighter color indicating where they selected.

    I am trying to save a snapshot that will restore the STATE of those buttons. What I am saving is in the screenshot attached.
    What other snapshot parameter button needs to be selected to pick-up the Mute Groups controls?

    In these snapshots I only want to save:
    1) mutes on FX1,FX2,FX3,FX4
    2) state of the button that controls MuteGroups 1-3

    The reason I am creating these snapshots is because I want to trigger them during performances with a midi foot pedal (CC). I am a bass player and also run front of house. I need these snapshots to be minimal (just muting effects and indicating MuteGroup's state. I am continually tweaking our MIX, EQ, etc... during our shows, so I absolutely need other settings to be unaffected.

    Thanks!
    read more...
    0 21
    • dwdata2000
      Paul_Vannatto When you save a snapshot, it saves all settings. What you are looking for are snippet functionality, which the X-Air consoles do not support. Only the X32/M32 has that functionality at this point. The screenshot you are showing are the snapshot recall scope and really won't do what you want to do. To control mutegroups using midi, this is accomplished using CC chan 2 36-39 for mutegroups 1.4 respectively. See X-Air Midi documentation here:
      https://behringer.world/wiki/doku.php?id=x-air_midi
      • Aug 12
  • New
    alexgun
    Newcomer - Level 1
    2022-08-04

    I accidentally plugged my UMC404HD to a 9V, 1.3A AC adapter (Harman Pro PS0913B-230). After I realised my fault, I switched the power source to USB. But my device not detected on my computer. The device shows Input 1 Clip & Midi In and Out indicator lamp turned on constantly (visualization in the picture below). Please help, what can i do to fix it?

     

    P.S. I already submit a care ticket, but somehow. It already marked as 'problem solved' without any reply. Is that normal?

    read more...
    0 27
    • alexgun
      WilliamR Hello, William from musictribe here. Can I have your case number so that I can look into this for you? It is likely that if you plugged in an AC power supply that there will be damage that a service center will need to repair.
      • Aug 3
      • Not working after accidentally plugged wrong power adapter
        alexgun Thanks for the reply. CAS-616280-T4H4N9 is my case number
        • Aug 3
      • Not working after accidentally plugged wrong power adapter
        WilliamR Dear Alex Gun 


        This is in relation to  CAS-616280-T4H4N9 
        Product:  Behringer UMC404HD 
        Serial:  S180846528BK1 



        Thank you for your contact.



        Considering what you have stated on your description when you submitted your assistance request please ponder that the UMC 404HD when not bus powered via USB must use a Positive Centre Negative PSU that supplies 5v DC.

        Unfortunately, when you used a 9V, 1.3A AC adapter it may have damaged your unit’s Power Supply and in these cases the unit must be serviced to understand the extent of the damages.

        To be possible to trigger the Assistance Request Process for your unit you must contact our Partner in Australia AUSTRALIS MUSIC GROUP to request assistance for your unit.

        Please see the contact details below for AUSTRALIS MUSIC GROUP below:


        Australis Music Group PTY Ltd

        UNIT 1, 1-11 Sydenham Road
        Marrickville
        Australia 61356

        +61 2 9698 4444



        https://www.australismusic.com.au/



        I hope this helps




        Thank you

        At your service,

        Pedro Rodrigues

        Music Tribe

        This email is intended exclusively for the addressee(s) named above and may contain privileged and confidential information. If you are not (among) the intended recipient(s), you may not copy, utilize, or distribute any of the information contained herein. If you have received this email in error, please notify us immediately via return email and delete the original from your mailbox. Thank you.
        • Aug 4
      • Not working after accidentally plugged wrong power adapter
        alexgun Thank you for the information
        • Aug 4
  • New
    Goldberg001
    Newcomer - Level 1
    2022-08-01

    I need Beringer ultradrive DCX2496 power supply replacement part,my own got burnt 

    0 43
    • Goldberg001
      StaffordAV It doesn’t look very burnt. If you know a local repair technician, these are fairly straight forward to fix; there is not a lot to go wrong. Most of the components are readily available.
      • Aug 1
    • Goldberg001
      Goldberg001

      Pls where can I get a new replacement part,I want to get one

      • Aug 1
    • Goldberg001
      ChrisEdwards1 Hi Goldberg001, please contact one of our Super Partners or Music Tribe Authorised Service Centre (MTASC) who will be able to advise further on parts availability and pricing. Please see the links below for lists of our global Super Partners and MTASC:

      Super Partners - https://www.tannoy.com/buy.html
      MTASC - https://www.tannoy.com/buy.html?type=POS
      • Aug 1
  • New
    rteglgaa
    Newcomer - Level 1
    2022-07-27

    Hi,

    Does anyone know what these advanced settings does?

    Thanks,

    Rasmus

    0 7
  • New
    rteglgaa
    Newcomer - Level 1
    2022-07-27

    Hi,

    As there is no user manual for the app for this mixer (that I know of), I have a question about what the marked features below are for:

    Thanks,

    Rasmus

    read more...
    0 12
  • New
    Behringer
    Triber Moderator
    2022-07-27

    The Projeto Acordes Magicos (PAM) aims at socio-cultural inclusion through music, prioritizing children and adolescents from the Novo Mondubim neighborhood in Brazil.

    Recently, Behringer and Music Tribe donated synthesizers and headphones to enhance PAM's music production and keyboard classes.

    We’re grateful to be part of Uli’s vision in making music education more accessible for the youth around the world.

    To find out more about Projeto Acordes Magicos and their cause, click here
    https://www.facebook.com/projetoacordesmagicos/posts/pfbid0tNtHGAK1xfMsX4QSgJQprYXxPx85P83fbpthwnNszEsMctAhbTsXyfsUM6UZPUQWl

    #MusicTribe #Behringer #Synthesizers #HelpingChildren #HelpMakeMusic

    ---
    Collaborate with our synth developers, share your ideas and get a chance to win free synthesizers by participating in our activities at our "Synthesizer and Drums Behringer Music Tribe" FB Group. We’d love to see you there!

    https://www.facebook.com/groups/KeysandDrumsBehringerMusicTribe/

    If you are a passionate and experienced mixed architecture hardware or embedded software engineer and would like to join the leading musical instrument team, please send your resume to [email protected]

    #WeHearYou #synthsforall #behringer #MusicTribe #synthesizer #synthesizers #drummachines

    read more...
    0 8
Go to page