• New
    Bascule
    Newcomer - Level 1
    2021-01-24

    Hi,

    I've had these so long I don't remember what they are ?

    Wondering if anyone can help?

    Cheers,

    Andy

    read more...
    0 231
    • Bascule
      Bascule The cabinet is about 25x50 cm
      • January 24, 2021
    • Bascule
      ChrisEdwards1 Hi Bascule, upon review, it appears you have a pair of DC1000 from the Series 90 range. I have included a copy of the brochure for you in the link below if this is of any help.

      https://we.tl/t-NCqpazmh1E
      • January 26, 2021
      • I've forgotten what these are!
        Bascule Cheers! :-)
        • January 26, 2021
    • Bascule
      Bascule Hi ChrisEdwards1 - Perfect, many thanks for that! :-)
      • January 26, 2021
  • New
    McQueen76
    Newcomer - Level 1
    2021-01-19

    Salve ho un paio di Tannoy DC8t, e devo dire che le sottupunte su un diffusore da migliaia di euro è stato realizzato veramente male.

    Nel senso che spesso si svitano ( forse per le onde sonore ) e i diffusori non sono stabili al 100% ma basculano.

    Avete delle  basi per sostenerle disponibili come il modello successivo (DC8TI) ??

    Vi allego una foto per farvi capire meglio.

     

    Grazie Danilo

    read more...
    0 113
  • New
    Riehmulus
    Newcomer - Level 1
    2021-01-15

    I have four CVS 6 ceiling speakers that have a transformer tap control. These speakers will be the front elevation and rear surround. Can anyone please tell me what setting I should use for a home receiver that does 100 W x7 at 6 or 8 ohms?

     

     

    read more...
    0 140
    • Riehmulus
      DavidKnighton Hello Riehmulus,
      For 8 Ohm output on a home receiver, you need to tap the LoZ setting on the transformer. Any other setting will go through a transformer tap, and you don't really want that for a home receiver.
      • January 15, 2021
    • Riehmulus
      Riehmulus Awesome. Is there a recommended pin usage for the molex connector?
      • January 15, 2021
    • Riehmulus
      Riehmulus I used pin 1 & 2 on one speaker and 3 & 4 on another and seems to get the same output level
      • January 15, 2021
      • Tannoy CVS 6 transformer tap
        DavidKnighton Are you referring to the speaker input? I do believe 1/2 is parallel to 3/4, so it shouldn't really matter. These speakers are designed to be daisy chain in the masses, but only in 70V/100V operation.
        • January 15, 2021
  • New
    AndrewKing
    Newcomer - Level 1
    2021-01-14

    Hi all,

    I have just been given a Tannoy TS12 and I want to add it to my hifi system of a Rotel RA10 Rotel 980 BX and Tannoy M3's. The 980BX just has 2 outputs for speakers so I will have to combine the speaker wires of the Sub with a set of the speakers (does it matter which one) also where on the sub do I attach them?

    Oh and is this a good idea

     

    Cheers

     

    Andy

     

     

    read more...
    0 393
    • AndrewKing
      PedroRodrigues Hi Andrew that effectively depends what speakers you are using and how you wish to use your Tannoy Sub, never the less the best option is to check the Manual for this unit where you have all the information you require https://wsi.li/dl/waQXZ235uGvZgeWR2/ .Thank you
      • January 15, 2021
    • AndrewKing
      AndrewKing Hi Pedro, Just check out the manual and I cannot see any practical advices how would you wire the sub woofer to the set up and I have just swapped my Tannoy speakers into another room and so this set up will be running Monitor Audio BX2 Thanks
      • January 15, 2021
      • How to wire a TS12 sub woofer
        PedroRodrigues Hi Andrew please consider that you need to to use a cable as stated below to interface your speakers first with an amplifier and them with the Sub. Please follow the signal flow stated on the Tannoy TS12 picture considering that the output of the Amp will input o the sub and the outputs on the sub should connected to the Mains on your system. Thank you
        • January 15, 2021
  • New
    Tannoy
    Newcomer - Level 1
    2020-12-29
  • New
    Tannoy
    Newcomer - Level 1
    2020-12-28
  • New
    Tannoy
    Newcomer - Level 1
    2020-12-24

    QCI Series
    bit.ly/Tannoy-QCI-Series

    High-Performance Dual Concentric In-Ceiling Loudspeakers for Installation Applications

    The Tannoy QCI Series Ceiling and Surface Mount Speakers are designed to serve our Installed Sound Customers.

    From: $110

    #Tannoy #QCISeries #Ceiling #Loudspeakers #Speakers

    read more...
    0 113
  • New
    Tannoy
    Newcomer - Level 1
    2020-12-23

    PCI Series
    bit.ly/Tannoy-PCI-Series

    Dual Concentric In-Ceiling Loudspeakers for Installation Applications

    The Tannoy PCI Series Ceiling Speakers are designed to serve our Installed Sound Customers.

    From: $225

    #Tannoy #PCISeries #Ceiling #Loudspeakers #Speakers

    read more...
    0 116
    • Tannoy
      Timons I love the idea of this product. I am in the US and am having a hard time finding a source to buy them. B&H lists the PCI series on their site, but says they may only have them available on April 16th (3 months from now!) Any suggestions?
      • January 17, 2021
  • New
    Egan
    Newcomer - Level 1
    2020-12-08

    Hello

    iam trying find a replacement 7" speaker for one of my tannoy sensys dc1. The speaker rattles loudly during some low frequencies. The outer ring of the speaker shows no damage. Coil issue perhaps. 

    0 181
    • Egan
      KyleJohnson Hi Brian, Kyle here with Music Tribe. You can contact our parts team by clicking on the Support link at the top of the page, then scroll down and select Spare Parts.
      • December 8, 2020
  • New
    Rammie
    Newcomer - Level 1
    2020-11-20

    Hallo,

    My midrange speaker is blown. Where or how can i get a new one (Tannoy Mercury MX2  JD9EA).

    0 296
Go to page