Statistics

306,234 members
190,603 posts
  • New
    willbone
    Newcomer - Level 1
    2022-06-01

    Hello!

    Why when I put the TC Helicon on a sound table in STEREO & MONO are more L than R??? Always is happening... in 2 or 3 sounds table and with new cables etc etc... I think it's a problem of the machine or of the configuration. 

    The only way to have the same L & R is in DUAL MONO.. not in MONO... not in Stereo. 

     

    The mode is in VOCAL PROCESSOR.

    Is it normal? Why is it happening?


    Thanks

    read more...
    0 81
    • willbone
      PedroRodrigues Hi willbone, thank you for your post, please consider that the VOICELIVE 3 EXTREME Output can be set up set up in different configurations such as the XLR Output Tab, the XLR Output Level parameter and the different Guitar Jacks Mode.
      You can use the XLR Output Mode parameter to select the output mode for VL3X.
      Parameter settings:

      Stereo:
      -The left XLR output jack carries the left stereo channel.
      -The right XLR output jack carries the right stereo channel.

      Mono:
      -The left XLR output jack carries the summed (with effects) mono vocal & guitar channel signals.
      -The right XLR output jack carries the mono vocal signal without effects.
      -The dry channel includes Tone and Auto-Chromatic Pitch Correction (if applicable).
      -The dry channel does not contain HardTune effect(s).

      Dual Mono:
      -The left XLR output jack carries the summed (with effects) mono vocal channel.
      -The right XLR output jack carries the summed (with effects) mono guitar channel.

      You can also use the XLR Output Level parameter to set the relative level of the signal going to the XLR outputs.
      Parameter settings:
      Mic Level:
      Typically, the best setting when connecting to a mixer/PA. This level closely replicates that of a microphone going directly into the mixer.
      Line Level:
      When connecting to a mixer/PA line inputs, this setting is a good choice.

      When it comes to Guitar Jacks Mode you may select from three modes to direct your backing track and guitar to the guitar outputs. Especially when working with Backing Tracks, this allows for maximum flexibility.
      The Guitar settings acts as the “normal” or “default” mode, sending guitar signals from the ¼” outputs in mono or stereo (depending on whether you have one or both jacks connected).

      With the Track L / Guitar R setting, Backing Tracks (summed mono) are sent out the left Guitar ¼” output, while your guitar signal (summed mono) is sent out the Right Guitar ¼” output.
      With the Backing Track setting, Backing Tracks are routed to the guitar outs.
      If both outputs are connected, the signal is in stereo. If one is connected, the signal is summed to mono.
      This mode allows you to have a two-component Backing Track where “the click” is sent to one ¼” output and “the track” to the other. These signals can then be independently routed wherever you wish.
      Usually, you will have “the track” go to the front-of-house mixer and “the click” to a stage/ monitor mix or the drummer.
      If you’re listening to Backing Tracks over your headphones, you’ll hear the split tracks as described here, with “the click” on one side and “the track” in the other.
      For a tutorial on PA basics, Yorkville has an extremely useful “PA Primer” guide (PDF):
      https://yorkville.com/downloads/other/basicpaprimer.pdf

      There is also a great video episode covering Mixer Setup with TC-Helicon devices:
      https://www.youtube.com/watch?v=qq0AOtafIjs
      Regarding your last question the Guitar output please see the text marked in yellow as effectively you are correct, never the less to effectively provide you with you option regarding the output of the VOICELIVE 3 EXTREME will only be complete with the information present on the picture below
      • Jun 1