Statistics

269,514 members
149,223 posts

Sort

Sort

Discover

  • New
    mjbworship
    Newcomer - Level 1
    2021-11-02
    XR18 No Signal for Inputs | Live Portable Sound

    I recently purchased and have been trying to set up an XR18. I haven't had any issues with connection, but when I'm connected and have an instrument or microphone plugged in to any of the inputs, I don't get any signal registering at all. Regardless of gain setting, there is no action on the meter.

    I've tried the standard resets and troubleshooting, but none of those has been a solution.

    I've attached a current scene file if that helps.


    View Attachment
    read more...
    0 6
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • mjbworship
      Nigel67 Hi mjbworship. Apologies for the delay in getting back to you. Are you using the XLR input when plugging in a microphone, and is the microphone you are using a dynamic or condenser, i.e does it require phantom power? The XLR input is for microphones and the jack input (hole in the middle of the XLR) is for line input. I can see from your scene you sent, that for Input 1, the Mic Gain has been turned all the way down. Try turning this up when the microphone is plugged in. You should then be able to see signal on the meter next to the fader in the edit software. For the microphone input, are you using a balanced XLR - XLR cable? I would start by just plugging in a media MP3 player of some kind. That will be a line level input and you will not have to worry about phantom power or not. Try a number of inputs to confirm which inputs are working and which are not. If you are still not having any success, I would advise raising a Technical Support ticket with us and we can advise further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket. If the unit is brand new, then I would also contact the seller that the unit was purchased from and advise them of the situation. They may also be able to help you further with the issue, but also, if the unit is still within 30 days, and is faulty, you will be able to request a DOA replacement so better to advise them sooner rather than later.
      • November 7, 2021
  • New
    Jonboyfzs600
    Newcomer - Level 1
    2021-08-15
    Tweeter not working on B215xl | Live Portable Sound

    Pdf attached showing my replacement of loose bulb holder on crossover unit


    View Attachment
    1 26
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • Jonboyfzs600
      Nigel67 Nice. Great set of clear and precise instructions. May come in very useful in the future. Thankyou. Not so sure about the footwear, I am more of a Star Wars sock type of person. :) All the best
      • August 15, 2021
  • New
    churchsound
    Newcomer - Level 1
    2021-05-26
    M32. How to connect speakers and subwoofers | Live Portable Sound

    Hi,

    I am helping my church to connect 4 speakers and 2 subwoofers by the attached diagram. 

    on the M32 menu. I am not sure how to assign outputs = Bus so I can control volume for subwoofers.

    Would you please help?

    Thank you so much,

    Loc


    View Attachment
    read more...
    0 60
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • churchsound
      DavidKnighton Hello churchsound,
      My best advice is to leave the LEFT MAIN and RIGHT MAIN speakers setup per the diagram. The SUB send I would highly recommend using a single mix bus or single matrix. Sub level is going to need to be even coming from both sides, so there's no need for independent level control. You're just burning an extra output that way. If using mix bus, use a POST FADER mix bus, such as bus 9.
      • June 1, 2021
  • New
    RayClaus
    Newcomer - Level 1
    2021-04-08
    deleted mix bus fader in X32 edit | Live Portable Sound

    Somehow I deleted the mix bus fader 5 from my X32 edit for PC.  Is there a way to restore the fader in the screen.  It is present everywhere else and I can assign channels to it, etc.  But it just isn't appearing on the fader screen. If you can open the attached doc, it has a snapshot of where Bus 5 fader is missing, but you can see it's still available on the right side listing.  If I delete the program and re-install, it still shows up as missing.  When I import a scene from my X32 it still is missing the fader.

     

    Ray Claus

     


    View Attachment
    read more...
    0 58
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • RayClaus
      DavidKnighton Hello Ray,
      See screenshot below. While on the Bus/MTX layer, click the EDIT button above the layer select and a window will pop open. You most likely have Bus 5 deselected for that layer. Click on it to turn it blue and it should pop the bus back into that layer view.
      • April 8, 2021
  • New
    DannyKurywchak
    Contributor - Level 3
    2021-03-14
    X-Live Can Playback Old Songs but won't record new songs | Touring

    Hello all,

    At our rehearsal studio we have a x32 with S16 all works perfectly except for the recording on the SDCard.  It will playback old files just fine but won't record new tracks.  We did have to make a change a while back to allow the S16 to work properly and I think that routing change disabled the recording capability.  I have attached a scene, any help would be much appreciated.

    Thanks,

     


    View Attachment
    read more...
    0 86
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • DannyKurywchak
      RexBeckett Hi Danny, yes Routing -> Card configuration in your scene is not correct - it is set to record from the Card inputs rather than the normal analogue console and S16 ones. The most likely setup for your scene is to set the Card output routing the same as the Input routing. See X32-Edit screenshot below.

      In your scene, Routing -> Inputs has got some Aux In Remap set for for AES50-A 1/2 (Record) and Card 1-4 (Play). As the Aux channels do not appear to be used for anything, I have ignored this in the Card routing.
      • March 14, 2021
  • New
    ambard9
    Contributor - Level 2
    2021-02-24
    P16 issue | Live Portable Sound

    Hi, 

    I few of my channels to the P16 from the X32 come from busses instead of the channel direct out. The bus channels will not allow the signal to flow to the P16 when I mute the channel being sent to the bus on the FOH x32. All of my direct out channels continue to send the signal to the P16 whether the X32 channel is muted or not. I want my busses to do the same thing.

    What do I need to do differently? Channel sends to bus are post eq. All P16 tap points are also post eq. Scene is attached.


    View Attachment
    read more...
    0 113
    0
    Mark As Solved 0 Reopen Discussion 0
    • 2 Replies
      Oldest
    • ambard9
      RexBeckett Hi ambard9, that is the way that channel-to-bus sends work on the X32. If you mute the channel, it also mutes the bus send. If you mute via DCAs, and the DCA Groups mute option is off, it does not mute the bus sends.
      • February 24, 2021
    • ambard9
      ambard9 Thanks for the clarification. I was hoping a different tap point for channel to bus send would fix the problem. I will relay to the rest of my group. Thank you.
      • February 24, 2021