Statistics

254,418 members
132,103 posts
  • New
    mattprice500
    Contributor - Level 1
    2020-11-12

    Will an x32 compact retain all its setup as in fader positions, scenes etc when depowered/repowered. The scenario is in a church where very few have technical knowledge and powering up and down I need settings to remain.

    0 61
    • mattprice500
      KyleJohnson Hi Matt, Kyle here with Music Tribe. In general, yes. The X32 saves it's current state every 2 minutes, and it will always boot in the same state that it was last shut down in. The only exception would be the Main LR Fader which by default will drop to the bottom when booted, but you can change this setting so that the Main LR Fader returns to it's last used point when powered up.
      • November 12, 2020
      • X 32 Compact keeping settings
        mattprice500 Kyle. Thanks very much for this info. Just what I wanted to hear. Where do I find the setting for the Main LR fader ?
        • November 12, 2020
      • X 32 Compact keeping settings
        KyleJohnson It's in the Setup>Config menu, the option you are looking for is called "Safe Main Levels". If it's checked, the mains will drop down at power on.
        • November 12, 2020
  • rclh57
    Newcomer - Level 1
    2020-10-07

    Can I use my XR16 to connect to an SD-8 or SD-16 that I want to put remotely by our church's old sound panel where the mics come in and the amps are?

     

    Many thanks, 

     

    Robin

    0 64
    • rclh57
      RexBeckett Hi Robin, the XR16 does not support AES50 so cannot connect to an SD8 or SD16 stagebox. It may be better to consider an X32 Rack for this project.
      • October 7, 2020
  • JeffClarke1
    Contributor - Level 3
    2020-10-03

    Using an X32 in a church, the on-desk USB Socket for service recording is very useful!

    Prior to the Covid-19 lockdown we simply needed the sermons to be uploaded to the church website, after processing to .mp3.

    Now that something like "nearly-normal" services are being resumed, there are a number of members who, for various reasons, still feel uneasy about returning to church.  As a result the decision was made that the (already-shorter) complete service would be recorded and then uploaded to the website.

    Al recordings prior to the lockdown, were "perfect" and only failed through operator-error, e.g. forgetting to Stop the recording before the console was switched off, so producing a 0 byte file! 

    Since the resumption of services a problem has manifested itself: specifically, the recording stops, randomly, without any operator action or intervention and any file is reported as 0 bytes.  Sometimes this will happen once, e.g. last Sunday the recording was started deliberately early, within less than two minutes it had stopped, a subsequent restart  was initiated and the recording continued successfully to the end of the service.  On other occasions, e.g. the music group rehearsal last Thursday evening, there were at least three times when the recording stopped, each time with a 0 byte file.

    I raised this as a support issue with Behringer, asking for suggestions to avoid this random stopping of the record process, only to receive a link to a page where the process to retrieve a 0 byte file is given.  I pointed out that I did not want that particular information, helpful as it might be, but guidance on how to avoid a full service recording being puctuated by gaps where the recording stopped and being dependent on the operator noticing the stop and immediately restarting the recording.

    I have verified that this is not an issue with the particular USB Memory Sticks being used.  Both are 32 GB, different manufacturers and both have passed a soak test of writing test data to completely fill them and then verifying the recording by playing back and reading the data.  (I used a very usefull utility called "h2testw" for this.)

    So, after a somewhat lengthy preamble (sorry about that): does anyone have any similar experience or advice to offer how this problem may be corrected and/or avoided?

    TIA

    Jeff

    read more...
    0 250
    • JeffClarke1
      JeffClarke1 Thought I would update this thread, with the solution to the problem, found after several email messages with Behringer Support UK.

      Although Support never actually confirmed this, it would seem that, with the introduction of v4 Firmware, there is now a requirement to use a USB 3 Memory Stick. Doing so has enabled us to successfully record recent services without problem.

      Jeff
      • October 29, 2020
      • X32 USB Record Socket failing?
        VictorRusso Hey Jeff, are you still having this issue? Seem to be having the same issue, regardless of usb 2 or usb 3 (using usb 3 today and it failed mid sermon, subsequent restart seems to go for at least a good amount of time). Music Tribe, is there a fix for this issue or do we need to work on an alternative?
        • Feb 7
  • jwsandersjr
    Contributor - Level 2
    2020-09-14

    I'm running an X32 with the V4.02 firmware. I have a question about the display on the home screen when a channel is selected. On "home" there are small graphic versions for Gate, Dynamics and EQ. I thought I had seen these smaller graphs actually work (or be active, i.e., the "square" would move along the graph line in the gate display, similar to what is shown on the Gate tab). Recently these don't seem to be moving. I thought I had seen a post from someone else that might have mentioned such an issue but I cannot find that anywhere? Is this a known issue and is there a solution, or am I incorrect on the display?

    read more...
    0 77
    • jwsandersjr
      john0121 Hi Jim, I just checked this on my M32R and the smaller graphics on a Channels home screen do reflect the processing. Could you fill out a tech support case via the Support button and go through some troubleshooting with the team?
      • September 14, 2020
      • Home Screen display of Gate, Dyn and EQ
        jwsandersjr Thanks, John ... will do. I usually only have access to the board on Wednesdays and Sundays, so it might be a while. Other than the serial number, what else should I grab while I'm there? Any files needed and if so which ones?
        • September 15, 2020
      • Home Screen display of Gate, Dyn and EQ
        john0121 If you could send a video showing the problem and a copy of the scene/show file your using that would be fine thanks
        • September 16, 2020
      • Home Screen display of Gate, Dyn and EQ
        jwsandersjr Thanks, I'll get a video on Sunday, but will open the ticket today. Can you suggest a "title" or "subject line" for my request that would best help tech support understand what I'm asking?
        • September 17, 2020
      • Home Screen display of Gate, Dyn and EQ
        john0121 just use the title and description from your original post and a team member in your region will pick it up Monday
        • September 17, 2020
  • hppygo
    Newcomer - Level 1
    2020-09-09

    Designing a system for a bar restaurant.  Have a totol of 9 zones with 6 fixed inputs and a snake for band performances.  Can I use the X32 as both a sound board for the band and setup output zones with remote zone controllers (tablets in each location to selcect source and volume level) for the restaurant and multiple bars?  

    I haven't worked with the X32, but am guessing I can program the output Zones, just don't know if I can program mutliple tablets to control only certian functions such as selectiing source and controlling volume for each zone. 

    How many different tablets can control the X32 at the same time?  

    Can the tablets be programed or locked into specific function of the X32? 

    read more...
    0 55
    • hppygo
      KyleJohnson Hello, Kyle here with Music Tribe. Short answer, yes. The X32 has 16 mix busses as well as 6 matrix busses, so you can easily setup outputs for different zones. There are multiple apps you could use, the X32 app for iPad gives you full control over the console for mixing FOH. You could also use the MX-Q app for your zones, MX-Q is designed for performers to mix their monitors, but at it's core it really gives the user control over 1-2 bus mixes. So you could send busses to your zones and have an iPad or iPhone setup to control that zone with the MX-Q app. You could also control the separate mixes for each zone using the main X32 app from FOH.

      It's a fairly easy setup, just creating bus mixes and routing them to outputs. Or sending your main LR mix to Matrix channels, and routing those Matrix channels to outputs.

      You would need a wireless router connected to the X32, and then connect your mobile device(s) to the router as well.
      • September 9, 2020
  • fbcpanamacity2501
    Newcomer - Level 1
    2020-08-27

    At the church I work at we have an s32 connected to an x32 by a shielded cat6. Last night when we turned everything on the "mute all" button on the s32 was red and would not turn off when you press it. Has anyone else run into this and have you figured out a solution?

    read more...
    0 2,003
    • fbcpanamacity2501
      KyleJohnson Hello, Kyle here with Music Tribe. First things first, you should switch your cabling to Cat5E. Cat5E is the spec for AES50 and using different spec of cable can lead to clock issues. The MUTE ALL light being stuck on typically means the S32 is not syncing to the X32 correctly. Try switching around which ports are in use and try a different network cable. It's possible that the AES50 ports on one or both units need to be repaired. I recommend you contact us directly by submitting a Support ticket using the Support link at the top of the page.
      • August 27, 2020
      • s32 mute all stuck
        fbcpanamacity2501 It might be Cat5E, I would have to check. I have submitted a support ticket but haven't heard back just yet. I will switch the ports and see if that makes a difference.
        • 1
        • ·
        • August 27, 2020
      • s32 mute all stuck
        KyleJohnson I think I found your case, I will send you an email.
        • 1
        • ·
        • August 27, 2020
      • s32 mute all stuck
        fbcpanamacity2501 Thank you
        • August 27, 2020
      • s32 mute all stuck
        lewisamendez Same problem!! s32 mute all stuck . How did you solve it?
        • November 9, 2020
      • s32 mute all stuck
        KyleJohnson Hi Lewis, it's usually a Cable issue, a Sync issue or a hardware issue. Double check your cable spec, length and integrity. Make sure the Sync on the console is set to Internal/Local. If you can, connect from the other port on your console or try a different console if you have one. If you still run into issues, please contact us directly by clicking on Support and submitting a Technical Support ticket.
        • November 10, 2020
    • fbcpanamacity2501
      ChaseHoyt I’m having this same problem.
      • December 28, 2020
      • s32 mute all stuck
        KyleJohnson Hi Clifford, Please contact us through the support link at the top of the page for assistance.
        • December 29, 2020
  • jfreivald
    Newcomer - Level 1
    2020-08-24

    Hello,

    I'm a RF engineer with an audio problem.

    I have an old system that I'm trying to interface with that has a 0-60KHz baseband that I need to capture and play out in real-time. It looks like the Line In/Out on the UMC202HD will do the trick pretty handily at the 192KHz sample rate. The mux has a 135 Ohm interface. 

    Can any of you audiofiles tell me what the impedance is on the UMC202HD line in/out connections so that I can build the matching circuit?

    Also, can anyone confirm that the Line In/Out jacks will play and record up to 60 KHz of baseband simultaneously? I'm used to designing systems between 300 MHz and 20 GHz, so I'm a bit out of my element. 

    Thanks in advance!

    --Joe

    read more...
    0 173
    • jfreivald
      RexBeckett Hi Joe, I'm not sure if the UMC202HD will do what you want. I have measured some of the characteristics of my UMC404HD (same preamps and output drivers as the UMC202HD) and confirmed that they agree with the published specs.

      The frequency response of the preamps is specified as 10Hz - 50kHz (+0, -3dB)
      I measured the Line input impedance as 42K @ 1kHz (balanced)
      The frequency response of the outputs is specified as 10Hz - 43kHz (-0, +0.3dB)
      I measured the XLR output impedance as 100 Ohms @ 1kHz (balanced).
      • August 24, 2020
  • kkahukiwa
    Newcomer - Level 1
    2020-07-24

    So many glitches and mistakes in the code for this website..perhaps get your web designers to do. a debug and take some of the team from Music tribe through a user experience from login...

    The hover buttons are not intuitive , they dont highlight to go forward..

    So many hurdles that are unnecessary that stop a user from moving on to the next page..I couldn't even access the actual product i bought. It isnt even on the dropdown list at the end of product registration..

    so I had to make one up to finish..Could at least ceate a form that the user can type in their product if the developers haven't updated the page for a long time. This site get's a B for BA for belowwwwww average. If this is the process for an artist to join the 'tribe'..stink one haha, I wonder how many artists were actually engaged to want to repeat this process again..You need to create a 'care ticket??' to register a product. Just use the language that already exists , it's ok, we understand it..A care ticket..I had to watch a video just to find out what a 'care ticket' was..Hope you can see the funny side in all of this cos I think it's pretty fricken funny, that a music tribe's online front of shop is actuually not creative at all..so weird

     

    read more...
    4 64
    • kkahukiwa
      AlexLane Hi there, my apologies you are not having the best experience with the site. We are still in a process of development and are taking feedback on board for future improvements. A few of these issues you highlighted are already on the to do list and any others I will add to the list.

      Please do let me know the specific issues with the care ticket system, if a product was missing I would like to get this immediately addressed. Please feel free to mail me direct any time too, [email protected]
      • July 28, 2020
      • This Musictribe site is a contender for the worst internet site ever
        PetGerbil Or.... perhaps, This site is never getting any better and you're just stringing people along "Trust me,honest guv! sometime in the future we will sort it out. Remember kids, we're listening!!" That excuse must be at least 4 years old now, and has been perpetrated through two website "Revamps." Meanwhile, I'm here after spending 15minutes looking for a post I REPLIED TO!! this morning.!! I CAN'T FIND MY OWN DAMN POST !!! FFS!! As far as I can see, There has been no improvement to this site since it's inception. Just the usual "..bear with us, while we do sweet FA"
        • 2
        • ·
        • September 11, 2020
  • Stevorolo
    Newcomer - Level 1
    2020-07-12
    When u form a group of mics or instruments, can u then go into the group and adjust the volume of each specific mic or instrument? If so, please explain.
    0 72
    • Stevorolo
      TvR Hello Stevorolo,

      Yes this is definitely possible within the DP48.

      To do this, select the EDIT button on the top right at the INPUT CHANNEL section.
      Now you can navigate via the GROUP buttons, select the different channels assigned to that group with the orange coloured REVERB and PAN buttons and use the SELECT/EDIT button to adjust the levels.

      When you press the SELECT/EDIT button, you also will able of adjusting the pan options for that specific channel.

      Hope this helps!
      • July 13, 2020
      • Using Midas DP48
        Stevorolo Thank u so much. I will give it a try.
        • 1
        • ·
        • July 13, 2020
  • JosephLeeTaylor
    Newcomer - Level 1
    2020-06-10
    My Church has an X32 Producer by Behringer. I'm going to video someone in via live video conference. I'm using my laptop to conference them in. I need to run all audio through the board, so that it's heard in the house. I need a mix for the incoming audio and another mix to go back to the person being conferenced in. 1) I also need to be able to livestream services to youtube/Facebook. I need listeners to be able to hear the band, choir and preached word. Can anyone help us?
    read more...
    0 59
    • JosephLeeTaylor
      DaveMorrison

      @JosephLeeTaylor 


      This will be a basic live sound reinforcement gig with a separate mix for the livestream using one (or a linked pair) of aux busses sent back to the Card (USB).


      Treat the incoming audio stream as another source to be mixed in the live show.


      The live stream usually need a seperate mix to account for live instruments not being present in the room that receives the stream (Acoustics instruments).


      The essential parts needed to send the stream mix to USB 1 & 2 depend on how your board is configured and used. I don't suppose you want to sacrifice a pair of wedges for the livestream since you ought to have room to do both. If you can upload your latest scene file, we can look at it and further advise.


      Here are (older) instructions for saving/uploading a scene. https://behringerwiki.musictribe.com/index.php?title=Uploading_files_to_the_forum
      Upload by Choose File at the bottom of the window.

      • June 10, 2020
Go to page