Statistics

306,252 members
190,624 posts
  • RamondBedford
    Newcomer - Level 1
    2020-09-08

    Completd a repair ticket and requesting a RMA number for parts thank you

    0 97
    • RamondBedford
      AlexLane Hi Ramond, Could you please click "support" at the top of the page and create a care ticket, select "spare parts" and fill out the required details, thanks.
      • September 8, 2020
      • Spare parts
        AlexLane I will run your email address through the system and chase up for you
        • September 11, 2020
    • RamondBedford
      AlexLane I have contacted the guys over in the USA and asked they address these two cases as a priority, apologies for the delay!
      • September 11, 2020
    • RamondBedford
      AlexLane Hi Ramond, issue was because of date of purchase was required (should not be) and hidden field when ticket is non-warranty. Issue has been fixed now. :)
      • September 16, 2020
      • Spare parts
        RamondBedford So what do I do now to obtain an RMA Number. A gentleman from the U.S. sent an email out to me yesterday requiring some information about my amp. He has received that info that was requested and said he was going to get with the team.
        • September 16, 2020
    • RamondBedford
      RamondBedford Hello Alexander, I see Music Tribe has sent me a new amp. But apparently there's something wrong with this one as well. Soon as I plugged this one in the right channel protect Mode was flashing then it goes in protect mode as well
      • October 16, 2020
      • Spare parts
        AlexLane Hi Ramond, sorry to hear that. Is it the same issue as before? I ask as it could be the same root cause of the problem.

        Can you detail exactly what is plugged into the amp, conditions of failure.

        In particular, what speaker and the specs of the speaker (or speakers) is plugged into the channel going into protect mode?
        • October 19, 2020
    • RamondBedford
      RamondBedford Nothing was connected. When I received the package Friday evening, I just plugged it in and it went straight into protect mode straight out of the box
      • October 19, 2020
  • rockdeschel
    Contributor - Level 1
    2020-06-04

    hey everybody,

    i´m looking for a PSU for a X1204USB mixer. Deos anybody know where i could purchase one or if there is a similar one that fits?

    Thanks

    0 82
    • rockdeschel
      RexBeckett

      @rockdeschel 


      Hello Samuel, welcome to the community.


       


      I suggest that you raise a Care ticket for Spare Parts explaining your requirements. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

      • June 4, 2020
  • AComo
    Contributor - Level 1
    2020-05-19

    Anyone know where I can get replacement crossovers for this PA? 2 of the caps burst open on one of the boards. Can't seem to find them anywhere

    0 95
  • AndyC55
    Contributor - Level 1
    2020-05-19

    Any one know where I can purchase the USB cable for the TC Electronics Vicious Vibe?

    0 70
  • JohnnyO
    Contributor - Level 2
    2020-05-10

    Hi, anyone know where or if it's possible to purchase any TC Electronic Smorgasbord of Tone blank, unpainted un-drilled pedal enclosures and black knobs? Looking for 3 enclosures and 12 knobs to complete a project for personal use to match the 4 TC pedals currently being used. Thank you!

    read more...
    1 174
  • Josecañon
    Contributor - Level 1
    2020-05-06

    Hola buenas, tengo una etapa berhinger nx3000, esta averiada tiene varios transistores en mal estado el problema es que no encuentro los recambios exactos por estar las referencias aparentemente incompletas, haber si es posible una ayuda gracias. 

    read more...
    0 442
  • GaryHiggins
    Superhero - Level 1
    2020-05-04

    Does anyone know on what pins the cat5 cable carries power to a DP48 POE rj45 port? What voltage is required to power them via that port? The Hub4 manual says the remote power follows the 802.3at spec but it appears there are a few varieties of pin options within that spec, and perhaps with voltage as well? Using pin 4 and 5 (+) and 7 and 8 (-) with 24v dc does not do it. The power supply to the DP48 uses 24V DC. The P16M uses those same pins but with 12v dc and it works fine. Looking for POE injector options as the HUB4 seems to be quite lost at sea.

    read more...
    0 421
  • Paul63
    Contributor - Level 1
    2020-04-23

    I am trying to get a replacement speaker for the behringer unit I have 

    0 102
    • Paul63
      RexBeckett

      @Paul63 


      Hello Paul, welcome to the community.


       


      I don't recognize 6W120B8 as a Behringer model number. If you can find a different model number marked on it, I suggest that you raise a Care ticket for Spare Parts explaining your requirements. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form. 

      • April 23, 2020
    • Paul63
      NicJonesMT

      Hi there. 
      We do not provide spare parts to end users. Your best option now would be to contact the Care team via the support tab and we can try and help you further. 

      Sorry for the delay and the inconvenience. 

      • April 29, 2020
  • sonny2
    Contributor - Level 1
    2020-04-13
    0 62
  • Umbert0
    Contributor - Level 1
    2020-04-11

    Hi,

    Would be possible to buy a FCB1010 main board pcb spare part?

    0 172
    • Umbert0
      RexBeckett

      Hello @Umbert0 , welcome to the community.


       


      I would try opening a Care ticket for Spare Parts explaining your requirements. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

      • April 11, 2020
Go to page