289,850 members
172,414 posts
  • New
    Newcomer - Level 1

    Does the Klark Teknik DI-10 have a buffer that feeds to the through put?

    0 89
    • Aldersyde
      DavidKnighton Hello Aldersyde,
      The DI 10A specifically does not have a buffered through. It is tied parallel to the input.
      • April 9, 2021
  • New
    Newcomer - Level 1

    Hello. first post here from the USA thanks in advance for any help.

    Just got this used 360 and thou it passes audio with no issue both A & B EQ has no effect on said signal.


    On a side note, I'd like to know what these 2 holes on the back marked "In put TX and Out put TX" are for. Is that a switch inside the unit (I see something white in there but not sure what it is)? Is that why I'm not getting anything more than by-passed signal?

    Seiral #36514


    Hopfully some one will know what the trouble is and leave a reply, I don't like flipping switch's on (or off) with out knowing what they do.

    0 125
  • New
    Newcomer - Level 1

    Hi everyone,

    I recently purchased the 76-kt compressor and im absolutely loving it. I am aware of the rear vu meter adjustment pot as stated in the start up guide but there is also a small hidden screw directly underneath the vu meter that i have messed around with (which i regret doing) i dont know why i messed with it, i was just curious what it did. 

    Im worried ive somehow messed up the calibration now as i presume this screw is factory set and shouldnt be altered. I can see that you can turn it clockwise and anticlockwise one turn and then it becomes stiff, you then screw further past that stiffness and it sort of resets to the loose, clockwise/anticlockwise setting as before.

    Am i ruining the screw by turning it over and over to see what it does? is it some sort of spring that i am unwinding?

    Id really appreciate any technical information to settle my mind on how this screw works and what you should do with, if i have perhaps ruined it by over turning it, or if i am just worrying too much?

    Thanks ever so much in advance.

    0 122
    • bgbdarby
      ChrisEdwards1 Hi bgbdarby, I can see you have also submitted a case for this inquiry which I have just responded to. Please keep an eye on your spam and junk folder for my response and if you can't find it please let me know.
      • March 24, 2021
      • 76-KT VU Meter screw directly underneath meter function? help needed.
        bgbdarby Hi Chris, I replied to that email earlier. Did you see my reply? thanks
        • 1
        • ·
        • March 24, 2021
  • New
    Newcomer - Level 2

    I have a DM8000 that I can not connect to, is there a way to either find the ip address or do a factory reset.

    0 126
    • Philip719
      trentperkins Hi Phillip, have you tried setting your computer to DHCP and directly connecting the computer to just the DM8000 to see if it can at least point you in the right direction of what network the DM8000 is on? By default, the DM8000 is on the 192.168.1.x network, but unless you have an idea of what network it used to be on, it could be a challenge to refind it. And then pray that the previous owner did not have a password on it. You might be able to get it fixed by submitting a cares ticket. Once you are on the right network the software should be able to find it.
      • March 11, 2021
    • Philip719
      Philip719 Yes tried DHCP, and I do not know what network range the customer had it on previously.
      • March 12, 2021
    • Philip719
      PedroRodrigues Hi Philip719 , please consider that when setting up an Ethernet network with multiple DM8000 units, devices in the network will need to be set up with IP addresses.
      Before assigning IP addresses, please keep in mind the following considerations, the computer must be assigned an IP address, under Network Card Settings>Properties.
      Most computers set TCP/IP address automatically, but DM8000 devices require manual assignment.
      Initially, the computer IP addresses should be assigned as 192.168.1.X where range of X = 1 to 254. Each DM8000 device must also be assigned a unique IP address.
      The factory default IP address for all DM8000 devices is
      • March 16, 2021
    • Philip719
      drfwfwiz Disable all firewalls (seriously)
      • July 13, 2021
  • New
    Contributor - Level 2

    Does anyone have any idea when the Klark Teknik KT Madi are going to become available. I am in dire need of one, and there are none to be found!!

    0 91
    • GeorgeAukerman
      Nigel67 Hi George, I am sorry, but we do not have visibility of when product will be arriving in your country of residence. Please contact your local distributor and they should be able to find out for you.
      • February 22, 2021
    • GeorgeAukerman
      DavidKnighton Hello George,
      Have you checked for Behringer X-Madi? It's basically the same card as Klark Teknik DN32 Madi. The main difference is going to be price point and warranty.
      • February 23, 2021
  • New
    Newcomer - Level 1



    When I connect this unit to my PC via the USB cable I only get the Left side of stereo.


    I have tried ALL Pan positions / Input choices and thpough the level meter shows both stereo lines are OK and the Phones and other outputs give me full stereo I get nothing on the right side of the USB output.


    I tried all the same cables but using a UMC202HD and had no issues at all.


    Might my QX1002USB be faulty of r is there a settinmg I need to address?






    0 78
  • New
    Newcomer - Level 1

    Hello, can i use an Midas DL32 with a Midas Pro2 in combination with DN9650 and a CM1 AES50 Card?


    What is happening when i upsample the DL32 to 96 kHz? Do i get two AES50 streams with 16 or 24 channels or one stream with channel 1-24 and a second with 25-32? Or do i get one 24 channel AES50 Stream an lose channel 25-32? Can i still contoll gains over the converted AES50 stream?

    And an other question. Can i control the settings of the DN9650 via Macbook?

    And can i update and control Pro Boxes like DL231 with a Macbook? 

    Nomaly i dont want to get a windows device just to contoll these settings.



    0 268
    • flowaudio
      DanielPaine Yes. A DN9650 with AES50 card can bridge a Pro Series to A M32.
      Setting controls for the DN9650 can be done on a Mac or PC connected via network cable and accessed through a browser.
      You can not control preamps through the DN9650.
      Some Pro stage boxes can operate at 48kHz so you can directly connect to M32
      These include DL251,231 &15X series

      Bear in mind, the conversion of channels in a DN9650 is 1 to 1, regardless of sample rate. so if to use a KT-AES50 card for M32, you can connect to the primary for 48 bi-directional channels. Using the fixed AES50 ports for Pro series, each connection can only accommodate 24 channels. so port1: 1-24, port2: 25-48.

      at 48kHz the KT-AES50 outputs are duplicated on the secondary port. I'm not aware how it deals with inputs but I suspect will be disabled.

      Lastly, stage boxes can be updated via a computer using IO Updater, found on the website software section of any stage box.

      I hope this answers your questions
      • February 15, 2021
    • flowaudio
      TobiasWinkl Hi, it ist not possible to use the 48kHz stageboxes DL16/DL32 with the Pro Series Consoles. It works only the other way. You can set the blue ones from 96k to 48k. The Connection has to be direct from the the box to the desk. With the DN9650 and a AES50 card you can downsample the AES50 stream to directly connect a pro desk to a X32/M32.
      • March 15, 2021
  • New
    Contributor - Level 1

    Hi Support Team, can I use the DN32-USB card for my Midas M32C like a Midi-interface to controll my Keyboards and Synth from my DAW? Or is this feature implemented in the DN32-LIVE card? (or possible with both cards?) Do you have a Midi implementation Guide for these cards? Thanks and best regards, Martin

    0 169
    • Maroliboe
      PedroRodrigues Hi Maroliboe, effectively you can use any of the card you refer on your Midas M32C but not as a MIDI interface, I would suggest following the link below to access information on both cards Thank you
      • January 29, 2021
    • Maroliboe
      Maroliboe Thank you for your feedback, I have seen this docs, on page 2 in the english product information document you can read at the top: „Your console’s recording capability just got even more robust, thanks to the new DN32-LIVE Expansion Card and USB Audio/ MIDI Interface.“ Is it possible with DN32-Live to send Midi via USB to the Midiports to control external Keyboards/Synthesizers??
      • January 29, 2021
      • Midi usage DN32-USB vs DN32-LIVE
        Maroliboe ... so is it working like a „true“ midi-interface?
        • January 29, 2021
      • Midi usage DN32-USB vs DN32-LIVE
        Paul_Vannatto The answer is no. The DN32-Live (as well as the X32-Live) card does not have a midi interface. The console itself has a midi interface that is designed to be used in conjunction with a midi device to control the console (mutes, faders, etc.) only. You are misinterpreting that line in the document. My read is that the DN32-Live expands the recording capability along with the USB Audio (and MIDI interface - for control).
        • January 29, 2021
    • Maroliboe
      Maroliboe Thank you very much, Paul, for your help :) it helped me in my decision how to route midi in my setup in the best way (and sry for multiple posts :)
      • January 31, 2021
  • New
    Newcomer - Level 1

    Is this utilizes Belden tactical Cat 5e cable??

    0 131
    • h941224
      PedroRodrigues Hi , please be aware that any questions regarding Behringer product must be addressed on the Behringer Community page and not on the Kark Teknik community page reserved for question regarding product lines for this bard. Please consider that the NCAT5E-50M is a Cat5e, Neutrik etherFLEX with a RJ-45 EtherCON (not the regular RJ45!) connector. Thank you
      • January 19, 2021
    • h941224
      GaryHiggins As Pedro said this is Neutrik cable not Belden. I've never bought a Neutrik product ever that wasn't of very high quality . I bought one of these snakes used several years ago and found the quality to be exceptional. It is Beldon tactical equal. Behringer brands/sells them but Neutrik makes the cable and the Ethercon connectors, Hirose makes the shielded rj45 and a Schill makes the reel, all great companies. That said I have been making my own now for quite a while with good success. if I were inclined to buy commercially, this is a very good choice and I would buy it again.
      • January 19, 2021
  • New
    Newcomer - Level 1

    I was recently made aware of the bypass on the 76-KT, and was wondering if the KA-2A has an option?


    0 140
Go to page