Statistics

254,489 members
132,177 posts
  • New
    GpDav
    Newcomer - Level 1
    2021-09-01

    Church installation.  M32 is never moved.

    Firmware version 4.04.1 installed.  Unit is approximately 2 years old.

    The last three church services, two week period, the M32 has "locked up" during the 1 hour service.  The display screen goes black, the preamp mic input still shows green LEDs active indicating signal into the M32.  All other LEDs go very dim.  The output goes away with no signal to the power amp.

    Unit is shut off via power switch and then turned back on.  Unit comes back on and operates normally.  Is this a software issue or hardware power supply??  Do we need to erase all the memory and reinstall software?  Getting ready to order a spare power supply.

    Please advise

    Thanks Dave

    read more...
    0 10
    • GpDav
      Paul_Vannatto Hi Dave, those symptoms seem like a faulty power supply. I would suggest you submit a warranty ticket by clicking on the Support above.
      • Sep 1
    • GpDav
      GpDav Hello Paul, Thanks for the quick advice.
      • Sep 1
  • New
    jjfredrick
    Newcomer - Level 1
    2021-09-01

    Is it plossible to save mix presets on SD Cards.  I am an audio enginner at the church that has 20+ band members that rotate in an out of the band each week.  Our church recently upgraded to a Midas M32, DL32, Hub4, and DP48 personal mixers and it would be ideal to be able to save each of their DP48 mixes to an SD card that can then be loaded on whichever DP48 unit they might be using in a given week they are volunteering.

    Admittedly, I'm still getting up to speed on this system, so perhaps I have overlooked an easier solution, but welcome any insights and/or suggestions for managing this scenario.

    read more...
    0 6
    • jjfredrick
      Paul_Vannatto Hi Jeff, yes you can save mix presets to either the 12 internal memory or 12 preset files on the SD card. Press the Setup and SD Rec buttons simultaneously and a menu will come on the screen with Load, Save, Delete, Read, Write, etc.). Select the Write, then one of the 12 group buttons to save to the SD card. It will save a file in the DP48M folder, such as dp48_sd_pre_01.bin (last 2 digits will be preset number). Selecting the Read, then one of the group buttons to load the desired preset from the SD card.

      If you want to have specific presets affiliated to specific musicians, I would suggest you create individual folders on a hard drive named by the musicians' names and place the appropriate preset files in them. Unfortunately the files have to be named exactly as shown above, or the DP48 will not read them.
      • Sep 1
  • New
    ReinhardKlamm
    Contributor - Level 2
    2021-08-31

    Hi folks

    I am now on the DP48 Trip using POE and this works fine. Now it would be great to get this POE Based Stagebox DL8. Any Information about this?

    0 15
    • ReinhardKlamm
      DavidKnighton Hello Reinhard,
      The product development is unknown at this time. I would check back periodically, as nearly all product releases are posted here in the community.
      • Aug 31
  • New
    rockbill01
    Newcomer - Level 1
    2021-08-31

    How are you!

    I live in Suwon, South Korea, and am an office worker who is interested in sound equipment.

    I had an idea for a wireless method during acoustic monitoring for a long time, so I sent it to AVIX & CUOSHOP the official Korean importer of Midas & Behringer, to propose and discuss it.

    The wireless WIFI monitoring app development book and STAGE WAVE & other monitoring APP Guide materials are attached as additional materials through AVIX.
    In the future if necessary, we will make it into a translated material and provide it.

    Currently, I am in charge of circuit parts in JIG and equipment assembly and manufacturing at Samsung VD and a primary supplier (Na & Na).

    In general, in relation to monitoring, it is a form of using one's own smartphone as a monitoring device from a wired method using

    Behringer P16-M to a wireless network method using WIFI Router. Innovative products are being launched to support you.

    We have analyzed STAGE WAVE App, which is currently the most emerging, and we would like to suggest a way to develop more advanced than

    STAGE WAVE App by identifying the improvements in the network of that APP.

    Advantages of STAGE WAVE: App compatibility / stability / Low latency possible (latency changes depending on the setting)

    Cons: Requires high-performance Router and mid-range performance smart phone
    Amount of high-power WIFI data / Monthly flat rate

    Advantages of the New Behringer App (temporary name): Intermediate performance Router / Entry-level Smart Phone support available

    Basic output WIFI data amount / Calculation of reasonable monthly fixed amount for users

    Development and sales of PC-only and WIFI Router combined (small-scale) models

    There are additional materials reviewed and analyzed to make this proposal, and ideas related to Line Up that will be upgraded in the future from

    this proposal model are also being prepared.

    Please review the contents first, and if you need interest or discussion about my proposal, please message & call.

    thank you.

    [email protected]

    082-10-2780-1587

    H.K.Oh (Hong Kyun Oh)

    read more...
    0 15
    • rockbill01
      Paul_Vannatto You have already posted this once before and got a response from the company. This is an end user forum. So it is inappropriate to post this here multiple times. Please delete this thread.
      • Aug 31
    • rockbill01
      rockbill01

      Hello. Paul_Vannatto

      Sorry for posting the same content multiple times.

      As you said, I clicked the function to delete the discussion, but the content is not deleted normally.

      thank you.

      H.K.Oh.

      • Sep 1
  • New
    vassallo90
    Newcomer - Level 1
    2021-08-30

    hey iv just bought a Midas f32 and noticed it's pre fader. Is there a Mod to fix to Post Fader?

    And who is available to do this working in Melbourne Australia?

     

    regards 

    0 23
    • vassallo90
      Dale_M There is a mod that can be done but we advise an official Midas repair centre perform it. For more info please submit a Technical ticket from the Support tab above.
      • Aug 30
  • New
    balky
    Contributor - Level 2
    2021-08-30

    Hello people!

     

    I wonder:

     

    The signal is comin in (-9  is set in configuration) the clip undicator lights up on the mixer itself

    on the screen in Dynamics/gates - no clipping occurs. As a matter of fact, nowhere clipping occurs but on the indicator above faders

    with -9 - meter hits between -12 and -4

    Even if I bring input trim to -18 (lowest) it still lights up. with -18 - meter hits between -18 and -20

     

    Any thoughts?  

     

    Thank you

    read more...
    0 21
    • balky
      Dale_M H|i there we would advise you submit a Technical ticket via the above Support tab so we can assist you in greater detail.
      • Aug 30
    • balky
      KevinMaxwell If all you see is +18 to -18 you are not controlling the gain and you probably have the gain set too high.You are just controlling the trim. You have left out a lot of detail in your setup. Are you using remote stage boxes, is there more then one console in this setup ? You can try going to the pre amp page (in setup) and bring down the gain on the channels that are clipping. If you only have one console hooked up in this situation you probably want to turn off "HA Gain Split" so you will have head amp gain control on each channel. Unless it is setup with "HA Gain Split" on for a reason.
      • Aug 31
    • balky
      balky Kevin, when I say that I set the gain on the mixer at -9 or -18, how do you say that my gain is probably too high. -18 is the total bottom on the mixer. Here are more details: this happens only on those channels that receive audio from DANTE card. Be it a computer sounds, or DAW return. The signal level in the daw does not clip is no higher than -.05
      • Aug 31
  • New
    DamienKyle
    Newcomer - Level 1
    2021-08-29

    What does 'Cable Red' refer to in the drop down menu for DL stageboxes in the Pro series Config tab? 

    0 17
    • DamienKyle
      Dale_M Hi there, it simply means "redundant" (back up)
      • Aug 30
    • DamienKyle
      DamienKyle Thought as much, thanks Dale. Why isn’t ‘C’ on the DL251 labelled Cable Red? I’m assuming ‘A’ = ch. 1-24 + outs 1-16, B= ch. 25-48?
      • Aug 30
      • Cable Red
        DavidKnighton probably because a DL251 has 3 ports, and users might consider port B to be Cable Red by mistake. Most if not all stageboxes that only offer up to 24 channels will only have a single port and a redundant port, 2 ports in total, so it's far less likely users will make a mistake when configuring their system with those stageboxes. I believe DL351, which has 4 ports, is similarly labelled as the DL251.
        • Aug 31
  • New
    dallaskruse
    Contributor - Level 2
    2021-08-24

    1. Is the only way to rename Group Names is via saving a .csv file as "names.csv" onto an sd card and then importing into the DP48

    2. How do I reset the Group Names on the DP48 to their default if I want to revert my group name changes?

    read more...
    0 17
    • dallaskruse
      Paul_Vannatto 1. The only other option at this point is to name the groups from the X32 Library, AES50 screen.
      2. You could create a names.csv file with Group1,Group2,Group3, (etc.) or whatever the default names were. I haven't seen those default name in over 2 years (so don't remember).
      • Aug 24
      • How to reset DP48 Group Names
        dallaskruse I'll be using the DP48s with different groups so I was hoping to be able to rename the Groups easily.
        • Aug 24
    • dallaskruse
      Paul_Vannatto What I've been doing is to setup preset files for each band, including the group names, then saving them to the 12 internal storage areas and/or to the 12 presets on the SD Card. I also store them on my laptop using folders for each of the bands.

      2 years ago (Aug 16, 2019) I did sound for a Woodstock 50th anniversary festival where I had to get 5 tribute bands and one local band through in 9 hours and used the 4 DP48 for their monitors. Since these were still beta (weren't released for sale until December), I had 20 minutes (or less) to make the changeover and teach the musicians how to use the DP48. Everyone loved them. The success was due to the stored presets for each of the bands.
      • Aug 24
    • dallaskruse
      Paul_Vannatto I had also started to develop an offline DP48 preset editor, but gave up because these files also include a checksum and my checksum generator routine never came up with the same checksum the DP48 was expecting.
      • Aug 24
  • New
    alpha7
    Newcomer - Level 1
    2021-08-21

    The mixer is hooked up to a Benhinger snake which keepa going on safety. We checked the snake at the audio store and they said the mixer is causing the issue. It'll make a pop sound and everything will stop making sound, nothing turns off though. Then the sound comes back on for about 3seconds to 1minute before it repeats. Any idea what it can be? Everybody suspects a board maybe bad or loose but if its software or if the parts aren't sold they said they will not touch it. Help thanks.

    read more...
    0 14
    • alpha7
      Paul_Vannatto First suspect is the AES50 cable. Is it shielded cat5e, 6 or 7 with ethercon ends? If so, check continuity (with a multimeter) between ethercon ends. If there is no continuity, find the break and repair, or replace the cable.
      • Aug 21
    • alpha7
      GaryHiggins As Paul said, cable is the major suspect. The condition you describe is classic aes50 ESD related. Just to quickly check some broken data wire and/or other physical cable problem exists, any cat5/6/7 will work for temporary purposes. The issue with ESD should not show up unless very dry conditions exist. Or the broken wire issue. You WILL need everything Paul said eventually though, but just for a quick double check, any good cable will work. Hope replacing a cable (the correct way) is that simple of a fix for you!
      • Aug 22
  • New
    redking
    Newcomer - Level 1
    2021-08-20

    Hi there

    I love my MR18 mixer / interface - what is the future of this lineup?  Looks like maybe it is near the end of its product cycle and maybe something else is in development?  Would love to see an "MR32" and see it go to the next level.  Maybe with 16 combi jack mic pres and make it expandible to another 16 with a stage box.  I could see this being a great solution for small studios that want the flexibility to take the rig mobile to record live shows.

    read more...
    1 44
Go to page