Statistics

285,275 members
167,220 posts
  • New
    Pstoltman
    Newcomer - Level 1
    2022-02-11

    When I plug the 205-D monitor in I'm hearing a distorted sound from the speaker. This occurs even with all volumes turned down. I have tried using a different power cord and multiple power outlets. Can anyone tell me what is happening? Any fix or is this something that needs to be sent in for service?

    read more...
    0 7
    • Pstoltman
      Dale_M Yes this will definitely need inspection, please go to the Support tab above and select Service to submit a ticket.
      • Feb 10
  • New
    panard0
    Newcomer - Level 1
    2022-01-31

    Hi everybody!
    I am looking for the part (number) that separate signals to tweeter and main speaker of an Eurolive VS1200F?
    does somebody knows it part#, name, cost or anything that can help me to fix a pair of floor monitors that I can only have sound of its tweeters?

     

    read more...
    0 8
    • panard0
      Paul_Vannatto The part you are referring to is called a crossover. Are you certain it is the crossover and not the 12" woofer? I would suggest you submit a repair or spare parts ticket by clicking on the Support (above) and fill in the form.
      • Jan 31
  • New
    Dellbhoy
    Newcomer - Level 1
    2022-01-06

    Hi there, I have a behringer eurolive f1220d floor monitor. It has been stored in my hut for over a year. I plugged it in to test it and at first it worked then after about 10 minutes it started making a farting noise then nothing. If I switch it on and off I'm only getting audio from the tweeter. I checked the main speaker in another cab and it's fine so it seems like an amp issue. Are these sold as a spare part. If so how much do they cost and where can I get one thanks

    read more...
    0 12
    • Dellbhoy
      DavidThomson1 Check you terminals from the amp PCB to your speaker connectors - could simply have been corrosion set in causing a poor connection
      • Jan 13
  • New
    PhilMW
    Newcomer - Level 1
    2021-12-14

    Were these ever produced with a wrinkle paint finish?

    0 8
    • PhilMW
      WilliamR Hello, William from music tribe here. To my knowledge, the BG410s Has only ever been available in black Tolex.
      • December 15, 2021
  • New
    DavidStackhouse
    Contributor - Level 2
    2021-11-21

    I'm interested in the B205D, and I see it has a hole in top into which an adapter may be placed, and then a boom attached to the adapter. But I can find no mention anywhere of whether this adapter is included or is it purchased separately, or if it's a part that Behringer makes and what would be the part model #, and if Behringer doesn't make it, then where would I get one, and what specs would it have to match.

    What I'm NOT asking about is this adapter here... 
    https://www.sweetwater.com/store/detail/B105DStdMnt--behringer-microphone-stand-mount-for-b105d-and-b205d 
    ...which is the adapter that would go beneath the B205D; i.e., the B205D would go on top of this adapter. I'm asking for details about the adapter that would plug into the hole atop the B205D, and then a boom would be attached to said adapter I'm searching for.

    The adapter I'm talking about is clealry shown here: https://www.youtube.com/watch?v=jjTBJLHkZVg&t=57s

    Bottom line... what's the adapter called / what's the model #, and where would I find it? Thank you!

    read more...
    0 30
    • DavidStackhouse
      Paul_Vannatto The B205D comes with a short mic pole (approx 4") with 5/8" mic threads on each end. This can be screwed into the top hole (that has 5/8" mic threads) and a standard boom (such as those made by OnStage) can be screwed on to the top. My church uses 4 of these B205D spot monitors and occasionally we will add a boom (from one of the mic stands).
      • November 21, 2021
  • New
    Chrisjames66
    Newcomer - Level 1
    2021-08-31

    Help? Overheating? But what component?

    It works fine for a while then it starts to cut out. When it does the Clip light and Power light will cycle on/off together for a bit, then starts working again.

    Hard to pinpoint as the cause is intermittent and not repeatable.

    I have a bandmate with the same issue with his. My other 3 are fine. Anyone else have/solved this issue?

    read more...
    0 32
    • Chrisjames66
      Dale_M Hi there we would advise raising a technical ticket from the support tab above so we can assist you, we would also advise your bandmate also contacts us too.
      • August 30, 2021
  • New
    Sault8487
    Newcomer - Level 1
    2021-01-11

    Hello. I have an Xair 12 and would like to use passive stage monitors to eliminate a few cables on the floor. What would be the best way to do this?

    0 104
    • Sault8487
      Sault8487 I am using a Crown XLi 800 amp to power my main L and R passive speakers. Could I use an additional crown amp to power the Aux 1 and 2 for the stage monitors?
      • January 11, 2021
    • Sault8487
      KyleJohnson Hello, Kyle here with Music Tribe. You would need to use an additional amplifier. Depending on the model (And power ratings) of Passive monitors you use, you could look at the Behringer NX1000, NX3000 or NX6000 to power them.
      • January 11, 2021
    • Sault8487
      RexBeckett Hello Sault8487, if you want to use passive stage monitors then you will need power amps to drive them. The Aux outputs on an XR12 should be suitable for feeding most power amps. The Crown XLi 800 may be suitable if it matches the power rating and impedance of your speakers.
      • January 11, 2021
    • Sault8487
      Sault8487 That’s what I figured. Thanks for the comments!
      • January 11, 2021
  • New
    the1musicschool
    Newcomer - Level 1
    2020-10-30

    How do you change the fuse in a Behringer 115d speaker? 

    0 336
    • the1musicschool
      RexBeckett Hi Jason, the fuse on a B115D is located just above the power connector. Prise out the plastic carrier to reveal the fuse. Replace the fuse with one of the same rating. If it blows again, I suggest that you open a Care ticket for Service.
      • October 30, 2020
      • How do you change the fuse in a Behringer 115d speaker?
        the1musicschool That's the issue, how do you price out the plastic carrier to reveal the fuse?
        • October 30, 2020
      • How do you change the fuse in a Behringer 115d speaker?
        the1musicschool Please list specific instructions on how to remove the plastic carrier to reveal the fuse. We have a show in 15 minutes.
        • October 30, 2020
      • How do you change the fuse in a Behringer 115d speaker?
        RexBeckett Usually it is straightforward: Remove the power cable from the connector and use a small, flat-bladed screwdriver to lever out the carrier. I hope you got it sorted-out in time for your show.
        • October 31, 2020
  • PJWHEELER
    Newcomer - Level 1
    2020-10-27

    I have bought a Behringer feed back destroyer FBQ1000. I have a Yamaha MG16XU mixing deck with electro voice ELX115P powered speakers . when i connect the FBQ1000 to the FOH speakers, I can hear a hissing sound like the FBQ1000 has introduced gain into the circuit. when i remove the FBQ1000 and connect the speaker directly to the mixing deck the hissing goes away. is the FBQ1000 working correctly or is there something i can do to remove the hiss ?

    read more...
    0 269
    • PJWHEELER
      PedroRodrigues Hi Phil if you try to use the FBQ 1000 between the outputs of your mixer and inputs of you active speakers with "stock" settings, you will not get good results. The FBQ just doesn't know what to do with the signal. If your mixer has channel inserts, many of our desks have these on the Mic input channels, use an TRS 1/4" Y to 2-Tip Sleeve 1/4" plugs insert cable on the microphone channel only using just one channel of the FBQ 1000.
      If your mixer does not have inserts, don't play any music while setting up the FBQ 1000 between your mixer outs and speaker inputs. In this case, be certain both channels of the FBQ1000 are set with the same values. In any situation, please be certain the filters have been reset before you start.
      Set up the FBQ so that only 4 or 6 filters are in the Single Shot mode. Using you microphone please bring up the microphone level and softly let you system feedback until the Single Shot filter have all been used. Make sure that all the other filters are turn off. This is will be the maximum signal level you will be able to have on your microphone without feedbacking without touching the rest of your signal.
      More filters being used normally generates too much of everything and the signal will eventually be filtered out.

      Only in the situation of using a channel insert and the FBQ 1000 is only processing the microphone signal, you can add two roaming filters to search for changing microphone feedback.
      Please be aware that if the microphone is on all the time the FBQ 1000 can also interpret any intersustained tones in the signal has feedback and the unit will process it to get rid of the all signal

      The FBQ1000 can work well in a Live situation, but the stock" settings just do too much. Changing the setting to limit the constant searching for feedback controls the FBQ 1000 and feedback. If you find that some feedback frequencies always show up at your gigs, the FBQ 1000 can be used as a parametric EQ and you can "permanently" lock those frequencies down.

      .
      • October 28, 2020
    • PJWHEELER
      PJWHEELER Thanks pedro . I will try your suggestion . I have another question: my mixing deck only has channel group out . Is there a way of using those to add the FBQ to the mic channel only ?
      • October 28, 2020
      • BEHRINGER FEEDBACK DESTROYER QUESTION
        PedroRodrigues Hi Phil, to guarantee that you will have no issues, unfortunately no, as the unit was designed to have the implementation stated above
        • October 28, 2020
    • PJWHEELER
      PJWHEELER thanks Pedro !
      • October 28, 2020