Statistics

285,630 members
167,621 posts
  • New
    JackDarling
    Contributor - Level 1
    2021-10-26

    I recently got an X-Touch One to use with Logic Pro X. When I first plugged it in everything was working well, except that the fader wasn't controlling the selected track. After doing some research, I found out that there was new firmware to fix that. I updated and that solved the original issue, but know the Pan Knob doesn't seem to functino at all. None of the indicator lights will turn on and it won't control panning on the active channel.

    Does anyone have any insight about what might be happening here?

    Thanks!

    read more...
    0 264
    • JackDarling
      PedroRodrigues Hi JackDarling, thank you fo r your post, in this case I would suggest to check the video guide present on the link below: https://www.youtube.com/watch?v=SOHi26sqOks Thank you
      • October 30, 2021
      • X-Touch One - Pan Knob not working in Logic Pro X
        JackDarling Thanks Pedro, I followed the manufacturer's instructions to set up the device properly. As I said, panning was working until I updated the firmware (which I had to do to fix another feature that wasn't working).
        • November 2, 2021
    • JackDarling
      Yzzman1

      Hi - I am a working composer and I was pissed (understatement) when I started to have this exact issue intermittently after updating Logic. You'll notice when the Pan controls stop working in Pan/Surround mode on the Xtouch - the l/r pan stereo lights are also not illuminated. What I found that solves the problem - at least until it happens again - is to unplug the USB cable (or cables in the case of having an extender or multiple extenders) and plug it back in after a few seconds. Then delete the control surfaces from Logic and reinstall them via controller setup. If you don't unplug the USB cables and plug them back in - this method does NOT work. You have to unplug the USB cables

      • Jan 11
    • JackDarling
      imrank79

      Press the bank button either left or right 3-4 times and it will come back to Pan

      • Mar 22
  • New
    cbarnes
    Newcomer - Level 1
    2021-10-23

    I'm connecting the X-touch Extender to an Akai Force and using it in MIDI mode. Is there anyway that I can change the internal MIDI Recieve parameters? I want to the button light on/off to respond to CC messages instead of Note on/off with Velocity. For example, I want to turn on the button light for the first mute button. Can I change it from responding to Note-On Velocity 127 to CC 1 Value 127? Basically I can't send back the correct message to turn the light; the Midi Learn on the Force only lets me send CC to a MIDI track. Mapping inputs is no problem, but the button lights don't toggle the way you would expect. With some guidance I could update the firmware with https://hexed.it to change the internal params.

    read more...
    0 12
    • cbarnes
      DaveMorrison The Extender has no programmability. The assignments are fixed for whichever mode you are in. If the Akai can't send the message the X-touch expects to see, you would need some device in between to translate.
      • October 23, 2021
  • New
    shmengie
    Newcomer - Level 1
    2021-10-16

    Hi All:

    Just got my X-Touch One yesterday. First thing I did was upgrade the firmware (to 1.07). I see that when I switch the fader to Master, the LCD turns off. Is that right? I would have assumed it would change to Master instead of turning off. Just checking.

    Thanks for humoring a noob...

    read more...
    0 18
  • New
    ToddClemmer
    Newcomer - Level 1
    2021-10-16

    I am using an X-Touch with a XR18

    Updated my brand new X-Touch from 1.12 to 1.21
    Used MIDI-OX

    After reboot all my faders fly to the top as soon as a channel is adjusted on my XR18.
    They won't move back unless I pull them down.
    All other controls seem to work normal

    I am using X-Air 1.7

    read more...
    0 28
    • ToddClemmer
      lanis3333

      I am having the same problem. My setup is X-Touch connected to an X32 core in XCTL mode connected over Ethernet. EVERY fader on the X-Touch will fly to the top of it's travel as soon as a the fader is changed on the front panel of the X32 Core or in X32 Edit. Also, the faders will not move unless I manually pull them back down. I am connected to the X-Touch as my scribble strips populate and other functions work. I just really need the faders to work !!!! This is a brand new X-Touch also running 1.21.

      • December 3, 2021
  • New
    derschulz20
    Newcomer - Level 1
    2021-10-14

    dear knowing folks! i bought an m1 Mac Mini in February 2021 and did some tracking with Reaper and X-Touch - no issues: all LEDs were working, scribble strips showing track names, faders operated as expected. 

    October 2021: no LEDs anymore, no track names and faders on 0 or moving to 0!!!! But still working on as they should on an old Win Laptop 

    On the Behringer product page there is a firmware 1.21, so i tried to update - not with the M1 but with my older Lenovo Win10 Laptop unfortunately no success: the x-touch display read "1.21    1.04", but nothing works and the encoder LEDs showing "full left"

    Is 1.21 really the latest firmware? 

    I don´t know why it was working before and i don´t have a clue how to make it working again!

     

    read more...
    0 80
    • derschulz20
      PedroRodrigues Hi derschulz20, thank you for your post please consider that the latest firmware for the X-TOUCH is in fact 1.21.
      The process to update is the following:
      Please follow the link below to download the latest firmware for your unit.


      https://www.behringer.com/behringer/product?modelCode=P0B1X


      Windows users can use SendSX for sending the update file to the controller.

      Steps to update the firmware:
      Keep DISPLAY button pressed during power-on
      Connect X-TOUCH to computer via USB
      Use any MIDI SysEx dumper to send the update file (.syx), don't send faster than standard MIDI rate.

      -SendSX or MIDI-OX on Windows recommended

      -Snoize SysEx Librarian on OSX recommended

      Cycle power after the dump has been sent

      Confirm the firmware version by holding down the DISPLAY button during power on and you are ready to proceed with the connection process of your preferred mixer.
      Concerning the issue you have reported on your M1 Mac I would advise you to contact Apple directly as the new architecture released on the M1 may create issues on units developed for the Intel Chip architecture that is no longer used and any information on this matter is exclusive provided by Apple. Thank you
      • October 15, 2021
      • X-touch firmware
        derschulz20

        @PedroRodrigues: thank you, unfortunately idid what U told me before and I did it again


        • October 15, 2021
    • derschulz20
      derschulz20 but no success!
      • October 15, 2021
    • derschulz20
      derschulz20 I tried to update exakt as Pedro described, used a Win PC an a M1 Mac Mini, tried different USB cabel on different USB ports with different software and different transmission speeds -> the above picture is what i get. Looks like my unit is not able to run firmware 1.21! At least it is possible to step back to 1.15.
      • October 15, 2021
      • X-touch firmware
        derschulz20 and: Apple doesn´t care about my and other X-Touchs not working on M1 architecture! Their machine is up and running, it is the X-Touch which is not working as it could.
        • 1
        • ·
        • October 15, 2021
      • X-touch firmware
        PedroRodrigues Hi derschulz20, thank you for your reply, in that case we will require to look in to this in more detail, please follow the link below and submit an assistance request directly with our Tech Support Team so we can assist you with more tools. https://community.musictribe.com/pages/create-new-ticket?type=Technical%20Support&brand=Behringer Thank you
        • October 16, 2021
  • New
    Tango24
    Newcomer - Level 1
    2021-10-03

    Hi,

    Ive seen some vids on how to do it with Logic but since i only need to controll my MR-18, I dont have software at this stage. How do I replace the Function buttons with Bus 1,2,3,4 etc?

    Thanks

     

    Todd

    0 31
  • New
    Toinou75011
    Newcomer - Level 1
    2021-10-02

    Hey ! 

     

    I'm a VJ and I'd like to buy a Behringer X Touch for my lives showq, but I don't know if this product is compatible with Resolume Arena ? 

    Does anyone here use this controller for video ? 

    Tx ! 

    0 21
  • New
    JDLX
    Newcomer - Level 1
    2021-09-29

    Hi ! hI! I am an owner of the DAW Presonus Studio One 5.4 I would like to ask something about Behringer X touch one. Many users on the internet say that when you select a track from the x touch one , the track is not selected on the mixer of Studio One. Is this problem fixed with the latest firmware update(1.8) ( I have not bought x touch  one yet)

    read more...
    0 56
  • New
    studiorecording
    Contributor - Level 2
    2021-09-28

    The X-Touch 8 channel, the X-Touch One both work fine. But the extender will not show text.

    I have 2 extenders and both exhibit the same results.

    0 16
  • New
    Bru1978
    Newcomer - Level 1
    2021-09-27

    Hi!

    Is not possible use the editor with x-touch one. Why not for the x-touch one and yes for the mini?

    Can I assign parametrers in pro tools?

    Thanks!

     

    Frank

    0 77
    • Bru1978
      PedroRodrigues Hi Bru1978 have you tried all the steps present on the video below : https://www.youtube.com/watch?v=WgATdD_GsZo Thank you
      • September 28, 2021
    • Bru1978
      PedroRodrigues Hi Bru1978 please also consider that there are a few compatibility issues with Hui base controllers and Pro Tools 2020-12
      • September 28, 2021
    • Bru1978
      Bru1978

      Thanks Pedro for the reply! My x-touch one works fine in pro tools with the pro tools assignments. But my question is: can I assign another function in the fader like bus send? Or fx automation in the rotary knob? Thanks!

      • September 28, 2021
      • x-touch one EDITOR!?!
        PedroRodrigues Bru1978, that is exclusively set up on the PT MIDI commands configuration.
        • 1
        • ·
        • September 28, 2021
    • Bru1978
      DEFF123 My amplifier (Euorport PPA500) lights flash on off for 2-3 seconds when I turn on and turn off. No vocal reproduction
      • September 28, 2021
      • x-touch one EDITOR!?!
        DEFF123 What am I replying to? I don't have an answer. Am I to go to another screen?
        • September 28, 2021
Go to page