Statistics

267,862 members
147,372 posts
  • New
    WillBilliams
    Newcomer - Level 1
    2021-01-16

    I was recently made aware of the bypass on the 76-KT, and was wondering if the KA-2A has an option?

     

    0 110
  • New
    AudioForge
    Newcomer - Level 1
    2021-01-13

    Hi KT team, I've followed a previous post from before Xmas and contacted suppliers re availability of a pair of 2As in a bundle I need.

    Thomann replied with "sold out and not expecting any more". Please can you advise if 2A has been discontinued, I'm ready to order a pair of 2As, a pair of 76s and a dimension.

    richy

    read more...
    0 126
    • AudioForge
      PedroRodrigues Hi Audioforge, please be aware that I can confirm that the units are not discontinued, in regard of availability I would advise you to contact another reseller to request that information about these product as we do not have access to information of third party company that distribute our products. Thank you
      • January 14, 2021
      • KT2A / 2AKT
        AudioForge Great news, thank you
        • 1
        • ·
        • January 14, 2021
  • New
    edalku1
    Newcomer - Level 1
    2021-01-07

    Kdx 15

    0 88
    • edalku1
      Nigel67 Hi Edgar, I am really sorry, but I do not recognise this unit. Can you send me a link to the page and then I will get you the relevant information. many thanks
      • January 10, 2021
  • New
    sunsurf
    Newcomer - Level 1
    2021-01-05

    Hi folks!

    Do you see any problem arising if I replace the tubes in my EQP-KT by 2x 12AX7 ?

     

    regards

    Michael

    0 174
    • sunsurf
      DavidKnighton Hello Michael,
      The EQP-KT uses a combination of 12AX7, 12AX7A, and 12AU7 vacuum tubes. I would recommend ONLY replacing each of the tubes with the exact model type. Otherwise you run the risk of faulty operation and potential voided warranty should an incorrect tube cause damage to the other components.
      • January 5, 2021
      • Tube replacement EQP-KT with 2x 12AX7
        sunsurf Thanks for the fast response. I am aware of these formal regulations concerning potential damage or warranty. So the point is that using two 12AX7 will definitely lead to a damage in circuitry or is there a risk of damage?
        • January 5, 2021
      • Tube replacement EQP-KT with 2x 12AX7
        DavidKnighton I cannot give you a straight answer on that, as I am not well versed in vacuum tube technology. I would say at the very least there is a risk of damage, so probably in your best interest to stick with the model of tubes the manufacturer has selected.
        • January 6, 2021
  • New
    peterashley
    Newcomer - Level 1
    2020-12-14

    Hi has anyone tested a dm8000 with a barco clickshare cx50?

     

    0 150
    • peterashley
      PedroRodrigues Hi Peter, please be aware that we advise the implementation of the DM8000 must be done via the physical connections available on the unit. Effectively we have never tested the unit with that wireless solution but we do not advise any other implementation other than the one present on the manual for this unit. Thank you
      • January 13, 2021
  • New
    willowsam1
    Newcomer - Level 1
    2020-11-01

    Hi folks.

    Is the KT-2A going to be available again? I'm keen to have one, but if not I will look at other options. Thanks.

    0 84
    • willowsam1
      john0121 Unfortunately as we do not directly sell products to end users we are unable to provide any information on pricing and availability of products. You will need to instead directly contact one of our resellers/partners and they will be able to advise you further. You can find the details of our international retailers/partners at the following link:

      https://klarkteknik.com/buy.html
      • November 1, 2020
  • MikeMicMNR
    Newcomer - Level 1
    2020-09-28

    I purchased the 76-kt a few months ago. It's completely unusable due to the loud audio hiss. I was going to literally throw it away but then I thought of contacting you guys for help. I did create a ticket for technical support about a week ago but have yet to receive any reply whatsoever. The unit I have is completely useless. I mean just turning it on creates the most awful audio hiss. The higher the output, the worse the noise gets. I've tried everything from feeding it a hot input to avoid turning up the output level, to going through a gate to supress the noise but nothing seems to help at all because the hiss is very loud and can be heard behind the vocals or whatever I'm trying to compress. Any help?

     

    Thanks in advance. 

    read more...
    0 156
    • MikeMicMNR
      Nigel67 Hi Miguel. This is definitely not right and we need to get your unit in for repair. What was the ticket number for the case you submitted and I will check where it is in the queue. I am surprised that nobody answered it as we do normally clear the queues within 24 hours. Let me know the case number and we can go from there.
      • September 27, 2020
      • 76-KT (audio hiss)
        MikeMicMNR Thank you in advance Mr. Turner. This was the ticket number I was given: Ticket Number: CAS-141048-L2V5F9
        • 1
        • ·
        • September 27, 2020
      • 76-KT (audio hiss)
        Nigel67 Hi Miguel. I have found your case. I have asked the guys in Vegas to take a look at it when they get in and reply to you.
        • September 28, 2020
    • MikeMicMNR
      kherje Yes i have almost the same problem, but when i run a hot signal in, i get really good results, but the output has to be all the way down, if i go past 48 on the output, the hiss gets louder and louder, rediciously loud if you push it, no matter what the input level is, Even with no input connected so basically: you cant touch the output knob without it hetting really noisy, I guess i should return it? Other than that: tried it on bass, and the sound i Get with hot input is just midblowing, if it wasnt for the output problem this would be one of my favorite studio devices
      • November 13, 2021
  • watchmanso
    Newcomer - Level 1
    2020-09-22

    Hi, can I use the Klark Teknik DN9652 to convert a Dante signal into an AES50 signal? 

    Currently, I am hoping to replace our Behringer X32 board with a Yamaha TF5. Unfortunately, our X32 is connected to a Klark Teknik Dm8000 DSP which has an AES50 card, and the DSP is locked with a password. We wish that we could convert a Dante signal into an AES50 signal so that we won't have to mess with the DSP programming. Is this possible? 

    Thanks.

    read more...
    0 83
  • AlexNL
    Contributor - Level 1
    2020-07-13
    Hi, Anyone experiencing loss of subscriptions after powering down the DN9650? regards, Alex
    0 88
    • AlexNL
      AlexNL powering down = power down -> next day -> power up :)
      • July 13, 2020
      • DN9650
        Nigel67 Hi Alex, sorry but I do no know what you mean by subscriptions. Could you give me a little more information please. Many thanks
        • July 13, 2020
    • AlexNL
      AlexNL subscriptions is Dante terminology (i think). This is like 'patching' within the PRO series.
      • July 17, 2020
      • DN9650
        AlexNL I am unsure where this is stored, I assume the KT-DANTE card inside the 9650 stores this 'patch'.
        • July 17, 2020
    • AlexNL
      Nigel67 As far as I know, the dante device only stores a list of the device name/channel name of each of its receive subscriptions. The actual patching is on the computer. You would have to ask Dante to confirm this.
      • July 17, 2020
  • RGWINEDWARDS
    Newcomer - Level 1
    2020-07-10
    Trying to download new firmware so I can connect to my new DM8000. Website says the following (below) everytime i go to page (regardles s of whether i am logged in or not!!!!!!! Error 477 Suspended CDN resource Unfortunately, this CDN resource has been suspended. REALLY NEED to get this going today! Someone please help. my email is [email protected]
    read more...
    0 168
    • RGWINEDWARDS
      Paul_Vannatto I read in another thread that they have switched over to new servers for all of their websites and have run into some glitches. Yesterday I tried to get a file from the Turbosound iQ site and got the same error, unfortunately.
      • July 10, 2020
      • DM8000 firmware download not working
        RGWINEDWARDS Just heard the server change was 2 weeks ago!. My rep was just on a nationwide rep call and NO ONE in US has access to firmware at the moment. AND the Europe offices don't seem to answer any calls or support emails. I won't be using this product again.
        • July 13, 2020
      • DM8000 firmware download not working
        DavidBradshaw I just sent you a couple of emails with the firmware (and DM Designer software) attached
        • 2
        • ·
        • July 13, 2020
Go to page