Statistics

267,849 members
147,357 posts
  • mody1
    Contributor - Level 1
    2019-12-28

    Hello

     was wondering how to get this option and how mutch it cost ?

    0 114
  • tommypenngotti
    Contributor - Level 2
    2019-12-26

    Hello - I just purchased a Klark Teknik DN350 EQ that looks to be from the middle 80s where the 120V fuse holder(plug) is missing and there is just a hole on the back board ...there are fuses on the inside under hood. The seller is claiming just the "plug blank" is missing... although it does possibly look modified?? Any help on this appreciated . Thanks 

    read more...
    0 156
  • NASservice
    Contributor - Level 1
    2019-10-08

    Hi all,

    We have forgotten the password for one of our DM8000's, is there any way to do a hard reset or recover the credentials somehow?

    1 505
    • NASservice
      Distinctap

      Following ?

      • October 8, 2019
    • NASservice
      DavidBradshaw

      There is a way to access a locked DM8000- I'll contact your guys directly to share.

      • November 27, 2019
    • NASservice
      todd_lewis

      David,


      I am not able to connect to the DM8000 at all. Can you contact me?

      • May 18, 2020
    • NASservice
      RexBeckett


      @todd_lewis wrote:


      David,


      I am not able to connect to the DM8000 at all. Can you contact me?





      @todd_lewis 


      Hello Todd, welcome to the community.


       


      Your post may not be noticed by anybody who can help. I suggest that you raise a Care ticket for Technical Support explaining your problem. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

      • May 18, 2020
    • NASservice
      todd_lewis

      Thanks. I finally got connected to the box. However, it has a very old version of firmware on it. I need v1.5 of the DM software. Does anyone happen to have that file?

      • May 18, 2020
  • petermciver
    Contributor - Level 1
    2019-08-19

    Hello-

    I’m using a DM8000 for a DSP Control in a theater install.  I have a fleet to f turbosound speakers all fed audio over Ultranet.  I plan on coming off a X32 into the DM8000 and then out to a P16D.  The fire alarm company has installed a smart relay with a set of N/C contacts that open in an active alarm state.  I’d like to use the GPIO terminals to trigger a ganged mute for all of the ultranet channels.  

    Heres where I need some help.  I’m not sure of all the settings and the wiring terminals that I need to connect to make it work.

    I submitted a trouble ticket weeks ago and never heard back from Klark Teknik.  Anyone have suggestions?

    read more...
    0 457
    • petermciver
      Paul_Vannatto

      Hi Peter @petermciver,


      Welcome to the forum. I'm not experienced with DM8000 so I had a look at the manual. From what I can see, the GPIO can only control volume (page 55). In order to externally control mutes or gang mutes, it needs to be done via RS232 (page 43). One way to create an RS232 interface with GPIO (connected to the smart relay) is with an arduino or Raspberry Pi and an RS232 shield.


       

      • August 19, 2019
    • petermciver
      DavidBradshaw

      Hi Peter


      You can connect a NC/NO contact to any of the GPIO pins. In DM Designer add a 'GPIO Select' object to the design and nominate that to be connected to whichever GPIO pin you physically connect the NC/NO contact to. In DM Designer add a ganged mute to cover all the outputs and in parameters check the box to add a 'control input'. In DM Designer, connect the last output pin on the GPIO select for NC to the control input on the ganged mute. Load up the design and you are done. 

      • November 26, 2019
  • DavidBradshaw
    Solution Leader
    2019-06-06

    Klark Teknik DM DESIGNER 3.1 and DM KONTROL 3.1 are now available for download, via the downloads section on the DM8000 product page.

    DM KONTROL offers PC based customised control page creation and operation of a DM8000 DSP across an ethernet network, when deployed with the new DM801 serial to ethernet bridge.

    Check the downloads here:

    https://www.klarkteknik.com//Categories/Klarkteknik/Signal-Processors/Matrix/DM8000/p/P0B17/Downloads#googtrans(en|en)

    read more...
    1 492
  • Emadson
    Triber Contributor
    2019-05-29

    DM8000 Design 2.9.1 Software and Firmware available for download

    DM8000 Software and Firmware Downloads

    read more...
    0 449
Go to page