Hello,
I am trying to update a DM8000 system to use newer versions of DM Kontrol but it requires Firmware 3.2 for the DM801.
I cannot find it anywhere. It must exist as Version 3.2.1 for the DM801 is mentioned in the release notes for the DM Kontrol updates.
Can anyone help with this file?
Kind Regards
Justin
Greetings! I recently had an installation where the network was changed from one IP network to another. 3 out of 4 DM TCEs easily adapted and found the new network automatically. A fourth has reverted back to 169.254.whatever, and I have no idea how to get it back to the network everything else is on. I cannot find it in DM Kontrol, even if I rescan for devices. Any help?
As I am at the job site and really want this to be finished, a quick response would be amazing!
Hey, is there a way to aggregate the Dn9630 with another interface to use the outs of the interface to send to another destination other than the mixer (X32)?
I am interested in building a abelton live backing tracks rig,I have a Midas pro1 console in which I want to use as my board for virtual Sound check but also want the ability to use for mixing backing tracks for live performances, so any suggestions in which klark teknik dn9652 or dn9650 also using the kt-usb network card for multitracks, thank's
Thanks probably go the dn9652 route and buy the aes 50 card and the kt-usb 2.0 card
I am HOPING to use the DM8500 as the brains of my entire installation. Part of that requires being able to use TCEs to send signals to the GPIO outputs… but I can’t for the LIFE of me figure out how to get ANYTHING to talk to the GPIOs or generate logic inputs of any kind)! I would LIKE to have buttons on the TCEs be able to trigger various GPIO pins hot or cold (as well as other logic within the system), but I have not found a way to do that AT ALL. To me that seems like a pretty basic function (that apparently was available on the previous wall controllers), but I can NOT find it.
I have one GPIO input (or any logic input) signal that is critical to the audio design, and I need to trigger 4 GPIO pins which will be used to control various presets on a digital SDI switcher (to include choosing which HDMI inputs will send the audio to the DM-8500 given various settings).
Is there a Logic input setting that I can trigger from a DMTCE? Unfortunately, due to a lack of great documentation, I chose this system with the assumtion that this would be a given, but now that the entire system depends upon it, I am finally able to figure out that it might not work. I am really hoping for a simple solution I just don't know about yet!
HELP?!?!?!?
Hi!
I have a situation where it would be GREAT if the DM8500 could send a web message via ethernet to control another device (in this case a Black Magic Design Video matrix). When I looked at the Command String Module, it LOOKED like it was designed to send and receive DPT strings and turn them into GPIO output information, but not so much to create custom strings strings BASED upon what would otherwise be a GPIO output (from the DM TCE). I could use the GPIO outputs and connect them to a Raspberry Pi to do the translation, but I was wondering if there was an easier way to do it.
So far my base design has been compiled, but I have not yet downloaded the design into the DM8500 itself yet, and as a result have not been able to fully explore the DM KONTROL. Is that where the magic happens? I am guessing that there will need to be plenty of more work on my design when it comes to logic ins and outs, but that will probably need to happen experimentally when I start using the DM KONTROL.
Thanks in advance for your help!
I have a DM8000 that I can not connect to, is there a way to either find the ip address or do a factory reset.
Hi, can I use the Klark Teknik DN9652 to convert a Dante signal into an AES50 signal?
Currently, I am hoping to replace our Behringer X32 board with a Yamaha TF5. Unfortunately, our X32 is connected to a Klark Teknik Dm8000 DSP which has an AES50 card, and the DSP is locked with a password. We wish that we could convert a Dante signal into an AES50 signal so that we won't have to mess with the DSP programming. Is this possible?
Thanks.