Behringer

Behringer

Brand

Behringer

207,660 members
79,757 posts
  • aaronjrg11
    Contributor - Level 1
    2019-10-03

    I recently just got my deepmind 12 and when i select the 'chord' button, the screen shows no 'record' feature. it instead only shows, 'armed' and when i play a chord, the screen is stuck on 'learning'.  selecting a 'trigger' never shows up as an option. similar situation in poly chord. I can only see an 'exit | rec |wizard | bank' and then same as above occurs. i play a chord, and it is stuck on learning.  any idea how i can fix this?

    read more...
    0 135
    • aaronjrg11
      stephandeutsch

      I got exactly the same problem with my DeepMind 12 - did you find any solution for it?

      • October 13, 2019
    • aaronjrg11
      stephandeutsch

      ok, my problem was a midi loop, my DAW sent the same chord I played - back to my DeepMind 12 bcoz I was in Midi Recording Mode. So if anybody has the same problem, try that out first!

      • October 14, 2019
  • paul_whitehurst
    Contributor - Level 2
    2019-10-02

    My amp powered off.  I replaced the fuse.  No sound.  I think it's in protect mode.  The display lights.  The light rings around the volume knobs are lit.  When I turn the power on the fan runs for one second and shuts down.

    Is this protect mode?  How do I get it out of protect mode?

    Thanks, Paul

    read more...
    0 150
  • HeikoKnuettel
    Regular Contributor - Level 1
    2019-10-02

    Why? 

    0 93
  • HeikoKnuettel
    Regular Contributor - Level 1
    2019-10-02

    It should let me configure the D, the Odyssey and the VC340.

     

    VC340: Synth found, but update not possible ("Failed, check network and press to retry")

    Model D: Synth is not found

    Odyssey: Synth is not found

     

    All synths are present in the device manager and can be played via MIDI or USB.

     

    read more...
    0 2,177
    • HeikoKnuettel
      DannyBudts

      It has nothing to do with the synths themselves but with some computer systems. I had the same problem. I closed all other audio us-drivers in the device manager, than the synths were recognised, I could update, I opened all drivers again...fine.


      I opened a case for it, the asked me for all details, they are aware of it and they are working on it. 


      Hope this also works for you. 

      • October 2, 2019
    • HeikoKnuettel
      HeikoKnuettel

      Thank you very much, that worked!


      I hope they get rid of this auto-selection of synths. Even if it worked (which obviously isn't the case) it is annoying if you have more than one synth, you always have to turn the others off.

      • October 2, 2019
    • HeikoKnuettel
      ChrisRose

      It's not working here for me either. The Synth Tool sees that my Model D is connected, but when I click on "Update" all I see is version 1.1.1 and a box beneath that which says "Loading".


      Nothing happens for about a minute, then I receive the same message: "Failed, check network and press to retry."


      Capture.JPG


      I've tried this on two separate PC's, both connected to the interent, and I get the same result on both machines. One is running Windows 10 64 Bit (latest version) and the other is running Windows 7 64 Bit (latest version). 

      • October 3, 2019
    • HeikoKnuettel
      HeikoKnuettel

      Update doesn't work for me either, on none of the 3 synths. Deactivating other drivers helped so that the tool at least found them.


      I added a rule for the windows firewall, but to no avail, updating doesn't work.


      My D is on Firmware 1.1.1 too.

      • October 3, 2019
    • HeikoKnuettel
      Talos

      It see's my Odyssey and I can change all the settings and sequences but when I go to the update page I just get ("Failed, check network and press to retry")


      Please release the OS updates seperately till the synth tool is fixed, and the rest of the settings as sysex

      • October 5, 2019
  • luchenbe
    Contributor - Level 1
    2019-10-02

    Hi, I use the DCX2496 PC software to control 2 daisy-chained DCX-es, the first connected via RS-232 to a PC running Windows 10 and an RS-485 link between the first and the second DCX. This works fine if I use a PC with a normal serial port, but on recent  notebooks without a serial port it does only see the first DCX when used with a USB-serial converter (I tried 2) . This is for both the older version of the DCX as for the latest generation. Maybe the DCX2496 terminal software does not work correctly with such adapters ? Is there a solution to this annoying problem or can Behringer adapt the terminal software (I use version 1.16a) so that it would work with such a setup?

    read more...
    0 139
  • Switchs
    Contributor - Level 1
    2019-10-02

    I don’t understand how to control what channels and which effects go to the monitors.

    0 296
    • Switchs
      DaveMorrison

      Hi @Switchs Screen Shot 2019-10-02 at 12.09.42 PM.pngPush the Bus 1 button shown in the picture. Raise the faders for the channels you want to send to the bus. Push Main LR when you're done and want to resume "normal" mixing.


      By default Bus 1 is routed to Aux out 1; this can be changed.


       

      • October 2, 2019
    • Switchs
      Switchs

      Thanks for your reply, you‘re very kind.


      Howerver, I was refering to the „bus“ that is routed by default to the headphone jack in the front of the unit.


      I understand you can route any bus you want to the jack, but by default, what is being routed to that bus? How do I change the levels for this bus? Are they the same as the main levels?

      • October 2, 2019
  • MacMcIlvaine
    Contributor - Level 2
    2019-10-02

    I was doing some testing and only had on mic. So I plugged it into in 1 and selected it as the source for fader 1, 2, and 3.

    The card is set for 8in/8out. Card out set to in 1-8.

    Eight channels show up in the recording software.

    But, only the first gets the mic.

    So, I slogged out two more mics and plugged them into in 2 and 3 and set the source for faders 2 and 3 accordingly.

    Now I get mic 1 on card out 1, mic 2 on card out 2, mic 3 on card out 3.

    So, what's wrong with the first setup?

    read more...
    0 106
    • MacMcIlvaine
      DaveMorrison

      @MacMcIlvaine 


      When the source is Local 1-8 under Card Output tab the signal is tapped from the preamp. When the source is Out 1-8 then the Output 1-16 tab comes into play. Input/LC is the preamp, thus remap doesn't work. Anything else will tap from the channel strip. Try Pre EQ.

      • October 2, 2019
    • MacMcIlvaine
      MacMcIlvaine

      Ok, I see.


      I tried Out 1-8 and pre EQ...didn't change. (I tried the other taps as well.)


      In any case it's not something I need to do. It was just being lazy, not going and getting a couple more mics.


      (And, I was testing something unrelated, just needed 3 source channels. )


       


      Thanks,


      Mac

      • October 2, 2019
    • MacMcIlvaine
      DaveMorrison

      @MacMcIlvaine 


      Hmm. It's always good to learn something new. Let's ask Paul @Paul_Vannatto 

      • October 2, 2019
    • MacMcIlvaine
      Paul_Vannatto

      Dave's (@DaveMorrison) explanation was correct, but not complete. On the Out 1-16 screen, you need to assign the DirOut Ch 01 to the first output, DirOut Ch 02 to the second output, etc. and assign the tap to something other than IN/LC. Then it will work.


       

      • October 2, 2019
  • T_ScottSmith
    Contributor - Level 3
    2019-10-01

    Hello all,

    I am hoping to get help figuring out what I have routed wrong on one of my sends on my X32.

    I have an X32 feeding 9-P16M's via ultranet. I have 2 drum channels (11/12) which I have tapped at In/LC and sent to Mix 1 on the mixbus which I have routed to P16 Channel 12.  my issue is when I mute sliders 11/12 I lose my signal to Mix 1 even though I have tapped them at In/LC, which by my understanding should be a send before all processing and muting. I am certain this is a simple issue I just dont know where to look for a solution. Thank you in advance for your time.

    read more...
    0 109
    • T_ScottSmith
      T_ScottSmith

      I suppose I should explain my goal. I want to be able to mute the drum FOH but for the druumer to still have ears. With the current configuration this is appears to be a hard no.... is it possible to to get this control. I know and have tested that anything going directly to the P16's is there still if muted. but i'm assuming because I have combined them in a mix on the mixbus so as to only use 1 channel of the P16 for drums that whenever I mute the input it also mutes the sends respective to that input... : (

      • October 1, 2019
    • T_ScottSmith
      Paul_Vannatto


      @T_ScottSmith wrote:


      my issue is when I mute sliders 11/12 I lose my signal to Mix 1 even though I have tapped them at In/LC, which by my understanding should be a send before all processing and muting.





      Hi Scott,


      Welcome to the forum. When you use a mixbus to feed a P16 channel, you are actually dealing with 2 sets of tap points. The channel sends (11/12) have taps (Input, Pre EQ, Post EQ, Pre Fader, Post Fader and Subgroup) and the mixbus assignment to the Ultranet output (In/LC, In/LC+Mute, Pre EQ, Pre EQ+Mute, etc.). The latter is with respect to the mixbus master fader. But there is one little "gotcha" with how the X32 is designed. The channel mutes always mutes the channel sends to the mixbus (unfortunately). Many moons ago I had a lengthy discussion about this and recommended that they add the +Mutes options to the channel sends, like they did with the output assignments so that users could mute FOH and still have the signals at the monitors. I was told no, that was not necessary.


       


      The workaround to this is instead of muting individual channels, assign them to a DCA - then mute/unmute the DCA. DCA only affects FOH not sends to mixbuses.


       

      • October 1, 2019
  • sarahm
    Contributor - Level 2
    2019-10-01

    I have an X32 Producer and I have several noisy channels which I can't use.  It's there even with nothing plugged into the XLR input.  It seems to be connected to the 48V phantom power.  On some channels it only occurs with phantom on, on others it is there all the time but worse with phantom on.

    read more...
    0 242
    • sarahm
      KenMitchell

      Hi Sarah ( @sarahm ), 


       


      Welcome to the community. It sounds like you might have some of the channel gains set really high but the best way for us to help is for you to save and post a scene file of your settings. 


       


      Ken

      • October 1, 2019
    • sarahm
      sarahm

      Hi Ken. Thanks for your reply.


      The problem happens even with the gain set as low as it will go.  Adjusting the gain doesn't make much difference to the level of the noise, but does induce loud pops.


      Scene file attached.

      A.scn
      • October 1, 2019
    • sarahm
      SethUldall

      @sarahm 


       


       


      In that scene, which inputs are noisy and which are 100% clean?  All of them?  Some of them?  


       


      Is it only the onboard inputs?  Or, does it also occur on the same channels if they're assigned to get signal from and AES50 or Card Source?


       


      If it is the onboard inputs only, does the noise move to other good channels assigned that (those) input/s?  For instance, if you assigned onboard inputs 1-16 to channels 17-32, do the troubled inputs behave the same way, in the same order?

      • October 2, 2019
    • sarahm
      sarahm

      Initially it was just channel 1 that was noisy, but it has spread like a disease and is now affecting inputs 1-8.  Channel 3 is the worst.


      The problem follows wherever the onboard inputs are routed.  If I assign inputs 1-8 to channels 9-16, then channels 9-16 are noisy.  If I route AES50 inputs to channels 1-8, then they are quiet.

      • October 3, 2019
    • sarahm
      SethUldall

      @sarahm 


       


      I don't know these consoles as well as some.  But, I didn't see any settings in the scene you posted that looked out of place.  No FX loops, gains all low, etc.  Unfortunately, it seems to be a hardware issue and will need repair.

      • October 4, 2019
  • Buchanfarmer
    Contributor - Level 1
    2019-10-01

    I have an MDX 4400 from brand new but I can’t find the documentation of how to use it.

    serial no - M0132161043, date code -109.

    please where can I find the docs to download?

    thanks, Doug.

    0 186
Go to page