Hi - I'm having the same trouble described in other posts, but none of the solutions has worked for me. I'm trying to integrate a Midas M32R into my Windows 10 PC through the KT USB card, with no luck. The card shows right up on my Macs, so it's not the card or its physical installation.
I'm getting the Code 10 error, and when I dig into the drivers I see that there's a second Microsoft driver attached to the device, and I think that's the problem. It doesn't matter whether I install the latest 4.59 driver or the 4.11 (these are the only options - no other legacy drivers on the site anymore). The installation goes fine, but the device won't work. I've uninstalled the device, restarted, reinstalled, unplugged the USB to let the computer re-populate the driver, etc.
The second driver is a Microsoft generic USB 2.0 driver, v.10. Do I need to somehow uninstall that one entirely, or will that mess up something else? I don't know how to do that anyway. I'd migrate to Linux, but I need to use this with vMix, which is Windows only. Anyone have any suggestions?
Thanks,
Dave
DN200
bit.ly/Klark-Teknik-DN200
Learn More: https://www.youtube.com/watch?v=wPRcsdrHZu4
Features dual parallel-connected combo XLR’s / ¼" TRS inputs. When connecting to the Combo XLR input, the input impedance is 20 kΩ, ideal for line level equipment and offering even lower noise performance. It's also equipped with a Stereo input mini jack which is ideal for connecting MP3 players or mobiles phones etc.
List Price: $129
#KlarkTeknik #DN200 #DIBox #Active #2Channel
Does the Klark Teknik DI-10 have a buffer that feeds to the through put?
Hello. first post here from the USA thanks in advance for any help.
Just got this used 360 and thou it passes audio with no issue both A & B EQ has no effect on said signal.
On a side note, I'd like to know what these 2 holes on the back marked "In put TX and Out put TX" are for. Is that a switch inside the unit (I see something white in there but not sure what it is)? Is that why I'm not getting anything more than by-passed signal?
Seiral #36514
Hopfully some one will know what the trouble is and leave a reply, I don't like flipping switch's on (or off) with out knowing what they do.
Hi everyone,
I recently purchased the 76-kt compressor and im absolutely loving it. I am aware of the rear vu meter adjustment pot as stated in the start up guide but there is also a small hidden screw directly underneath the vu meter that i have messed around with (which i regret doing) i dont know why i messed with it, i was just curious what it did.
Im worried ive somehow messed up the calibration now as i presume this screw is factory set and shouldnt be altered. I can see that you can turn it clockwise and anticlockwise one turn and then it becomes stiff, you then screw further past that stiffness and it sort of resets to the loose, clockwise/anticlockwise setting as before.
Am i ruining the screw by turning it over and over to see what it does? is it some sort of spring that i am unwinding?
Id really appreciate any technical information to settle my mind on how this screw works and what you should do with, if i have perhaps ruined it by over turning it, or if i am just worrying too much?
Thanks ever so much in advance.
I have a DM8000 that I can not connect to, is there a way to either find the ip address or do a factory reset.
Greetings! I have largely complete my initial design for a DM8500, made it look good, etc. When I went to compile it though, it listed several apparently unplugged modules that I can't find anywhere on the design. Maybe they are hiding behing a different module, but I can't find them. Is there a way to list all of the used modules with their associated ID numbers to facilitate in the troubleshooting process?
Specifically, the compiler says that High Pass 6-24 dB/OCt (ID=8) is not an input module, and that the same filter ID=11 has no input or output (none of the High pass filters that I can see in my design are ID=8 or 11). Also, modules 12-16 have the same issue. They include 2 Parametric EQs, 2 comp/Limiters, and another high pass filter.
It is possible that I created some modules early in the process before I knew what I was doing and then deleted them (or at least I THOUGHT I deleted them!). But if I can't find them and make them go away, I can't complie the design, and the machine is useless.
I attached a picture of my design. i would be happy to email the actual .dmd file, but apparently that can't be attached to the forum.
Does anyone have any idea when the Klark Teknik KT Madi are going to become available. I am in dire need of one, and there are none to be found!!