Klark Teknik

There should be a 250ma TD (slow blo) fuse on the back panel.

@PieterLauwers 

Maybe. It depends on your setup. Where are you using external effect and what effects are they? The XR18 already has very good preamps. I suspect your are using effects before the the mixer and the type of effect and it's input and output requirements maybe the source of your problem.

With a little more information, we can give you some advice.

Example:

- used effect: EHX Big Muff

- routing: instrument in, routed to aux, aux in effect, effect out plugged in mixer.

So, since the effect is plugged in after the input, the problem is with the effect ( tried Boss Overdrive also) or with the gain settings.

( I definitely play a lot better then I am in setting the electronics up!)

@PieterLauwers 

The way you have it setup makes sense for your apllication. The problem is a level and impedance mismatch between the mixer's line level output and the pedal's guitar level input.

Even if you can get the level low enough, the impedance mismatch will mess with your tone. An line level to guitar level converter (also known as  re-amp) will solve that problem.

Have you tried the mixer's built in Guitar Amp simulator and Tube Stage emulator. You can insert them in a (pair of) channel(s) to get very good amp simulation. Give it a try and see if you like it, or get a re-amp box.

I use the Tube Stage emulator as an effect on both melody strings.

so, probably, I will need a reamp box.

If I understand it right:

- the effects I use are guitar effects, build for guitar impedance, not mixer line impedance

- in order to fix noise problems with my outside effect string the mixer's line impedance has to be tempered, ergo the ReAmp.

Did I say that right? (Still trying to understand the mystic ways of a mixer)

Thanks!

@PieterLauwers 

Impedance and really hot levels are the problems. The Radial ProRMP would be a very solid interface, It's got a sweet little transformer that will make your pedals happy. The are many other fine brands of course.

As a bonus: After you record your parts, you can use your re-amp to manipulate your tracks after they are recorded,

Hi @AWhite 

To send 8 channels of 48k audio from Ableton to the X32, send the channels you want from Ableton on separate USB channels (eg. 1-8). Assuming you send USB 1-8, you'll want to assign AES50 (A or B) channels 1-8 to eight input channels. This would be the routing: Routing:Inputs: Channels. For example, you could put those 8 channels on X32 channels 25-32.

Of course, you could alternately put them on 1-8, 9-16, or 17-24.  The DN9630 will sync to the X32 through AES50 and Ableton will sync to the DN9630.

Is there an option to route them to 33-40 (aux ins) Maybe that's what you are showing in the image, but would I thin loose 8 ins on the 1-32?

@AWhite 

You can remap those the Aux inputs but Aux In remap is limited to 6 channels. That's why I didn't mention it.

Following ?

There is a way to access a locked DM8000- I'll contact your guys directly to share.

David,

I am not able to connect to the DM8000 at all. Can you contact me?

---

@todd_lewis wrote:

David,

I am not able to connect to the DM8000 at all. Can you contact me?

---

@todd_lewis 

Hello Todd, welcome to the community.

Your post may not be noticed by anybody who can help. I suggest that you raise a Care ticket for Technical Support explaining your problem. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

Thanks. I finally got connected to the box. However, it has a very old version of firmware on it. I need v1.5 of the DM software. Does anyone happen to have that file?

Hi Peter @petermciver,

Welcome to the forum. I'm not experienced with DM8000 so I had a look at the manual. From what I can see, the GPIO can only control volume (page 55). In order to externally control mutes or gang mutes, it needs to be done via RS232 (page 43). One way to create an RS232 interface with GPIO (connected to the smart relay) is with an arduino or Raspberry Pi and an RS232 shield.

Hi Peter

You can connect a NC/NO contact to any of the GPIO pins. In DM Designer add a 'GPIO Select' object to the design and nominate that to be connected to whichever GPIO pin you physically connect the NC/NO contact to. In DM Designer add a ganged mute to cover all the outputs and in parameters check the box to add a 'control input'. In DM Designer, connect the last output pin on the GPIO select for NC to the control input on the ganged mute. Load up the design and you are done. 

Hi @gtcode 

Yes, only 96kHz / 48 kHz. The idea behind the DN9630 was to be a lower-cost recording/playback option mainly geared towards our Midas PRO Series users. Prior to the DN9630, users would need to incorportate a Klark Teknik DN9650 w/ Dante or KT-USB card options (or third-party RPM Dynamics interfaces), which are quite expensive if you're simply looking to track shows or use for virtual sound check. 

The 48kHz option further add to the market for our M/X32 users -- as most people are using the 48kHz sample rate. Further, many of our 'Blue' DL15x, DL25x, DL231 Stageboxes only operate at 96/48 kHz so this is in line with those product ranges. 

Hi @gtcode 

Apologies, it really wasn't meant to be implied that way. Nearly all AES50 peripherals relating to PRO Series only 96kHz and 48kHz, such as the DN9680, DN9650, DN9620, DN9610, All 'Blue' I/O boxes, and lastly the DN9630. For M/X32 users, I think the majority of applications where a DN9630 would be used would be in the DN32-USB card is replaced with somethng like the DN32-DANTE card -- and typically users set the sample rate to 48kHz. 

Although it sounds like you were looking for a 44.1kHz solution and in that case, I understand your frustration.