Klark Teknik

Klark Teknik

Brand

Klark Teknik

242,690 members
119,086 posts
  • New
    Philip719
    Newcomer - Level 2
    2021-03-11

    I have a DM8000 that I can not connect to, is there a way to either find the ip address or do a factory reset.

    0 80
    • Philip719
      trentperkins Hi Phillip, have you tried setting your computer to DHCP and directly connecting the computer to just the DM8000 to see if it can at least point you in the right direction of what network the DM8000 is on? By default, the DM8000 is on the 192.168.1.x network, but unless you have an idea of what network it used to be on, it could be a challenge to refind it. And then pray that the previous owner did not have a password on it. You might be able to get it fixed by submitting a cares ticket. Once you are on the right network the software should be able to find it.
      • Mar 11
    • Philip719
      Philip719 Yes tried DHCP, and I do not know what network range the customer had it on previously.
      • Mar 12
    • Philip719
      PedroRodrigues Hi Philip719 , please consider that when setting up an Ethernet network with multiple DM8000 units, devices in the network will need to be set up with IP addresses.
      Before assigning IP addresses, please keep in mind the following considerations, the computer must be assigned an IP address, under Network Card Settings>Properties.
      Most computers set TCP/IP address automatically, but DM8000 devices require manual assignment.
      Initially, the computer IP addresses should be assigned as 192.168.1.X where range of X = 1 to 254. Each DM8000 device must also be assigned a unique IP address.
      The factory default IP address for all DM8000 devices is 192.168.1.201.
      • Mar 16
    • Philip719
      drfwfwiz Disable all firewalls (seriously)
      • Jul 13
  • New
    trentperkins
    Newcomer - Level 2
    2021-03-08

    Greetings!  I have largely complete my initial design for a DM8500, made it look good, etc.  When I went to compile it though, it listed several apparently unplugged modules that I can't find anywhere on the design.  Maybe they are hiding behing a different module, but I can't find them. Is there a way to list all of the used modules with their associated ID numbers to facilitate in the troubleshooting process?

    Specifically, the compiler says that High Pass 6-24 dB/OCt (ID=8) is not an input module, and that the same filter ID=11 has no input or output (none of the High pass filters that I can see in my design are ID=8 or 11).  Also, modules 12-16 have the same issue.  They include 2 Parametric EQs, 2 comp/Limiters, and another high pass filter.

    It is possible that I created some modules early in the process before I knew what I was doing and then deleted them (or at least I THOUGHT I deleted them!).  But if I can't find them and make them go away, I can't complie the design, and the machine is useless. 

    I attached a picture of my design.  i would be happy to email the actual .dmd file, but apparently that can't be attached to the forum.


    View Attachment

    read more...
    0 93
    • trentperkins
      trentperkins Any help? I may have to rebuild the whole thing again being careful to not experiment with modules I don't end up implementing. Even so, this seems like it should be a pretty easy fix to be able to generate a list of all used modules and their status by ID number.
      • Mar 17
    • trentperkins
      trentperkins Thanks Thim, not only does it work, it looks great! How do you get the lines to work at right angles?
      • Mar 19
  • New
    EvertonWilliams
    Newcomer - Level 1
    2021-02-23

    Hi I own a DN9849 4×8 PROCESSOR I LOST THE PROGRAM THAT WAS STORED IS THERE ANY WAY TO RETRIEVE IT AND THE MEMORY BATTERY PART#BR2330 IS THAT A RECHARGEABLE BATTERY OR JUST A REGULAR LITHIUM BATTERY 

    0 91
    • EvertonWilliams
      Nigel67 Hi,I am afraid that all User memories will have been lost. You will only have the factory preset memories. It is not a rechargeable battery.
      • Feb 23
    • EvertonWilliams
      EvertonWilliams Thank you
      • Feb 23
  • New
    GeorgeAukerman
    Contributor - Level 2
    2021-02-22

    Does anyone have any idea when the Klark Teknik KT Madi are going to become available. I am in dire need of one, and there are none to be found!!

    0 74
    • GeorgeAukerman
      Nigel67 Hi George, I am sorry, but we do not have visibility of when product will be arriving in your country of residence. Please contact your local distributor and they should be able to find out for you.
      • Feb 22
    • GeorgeAukerman
      DavidKnighton Hello George,
      Have you checked for Behringer X-Madi? It's basically the same card as Klark Teknik DN32 Madi. The main difference is going to be price point and warranty. https://www.behringer.com/behringer/product?modelCode=P0AZQ
      • Feb 23
  • New
    Saltykova
    Newcomer - Level 1
    2021-02-22

    Hello,

     

    When I connect this unit to my PC via the USB cable I only get the Left side of stereo.

     

    I have tried ALL Pan positions / Input choices and thpough the level meter shows both stereo lines are OK and the Phones and other outputs give me full stereo I get nothing on the right side of the USB output.

     

    I tried all the same cables but using a UMC202HD and had no issues at all.

     

    Might my QX1002USB be faulty of r is there a settinmg I need to address?

     

     

    Thanks,

     

    Mike

    read more...
    0 46
  • New
    flowaudio
    Newcomer - Level 1
    2021-02-13

    Hello, can i use an Midas DL32 with a Midas Pro2 in combination with DN9650 and a CM1 AES50 Card?

     

    What is happening when i upsample the DL32 to 96 kHz? Do i get two AES50 streams with 16 or 24 channels or one stream with channel 1-24 and a second with 25-32? Or do i get one 24 channel AES50 Stream an lose channel 25-32? Can i still contoll gains over the converted AES50 stream?

    And an other question. Can i control the settings of the DN9650 via Macbook?

    And can i update and control Pro Boxes like DL231 with a Macbook? 

    Nomaly i dont want to get a windows device just to contoll these settings.

    cheers

     

    read more...
    0 91
    • flowaudio
      DanielPaine Yes. A DN9650 with AES50 card can bridge a Pro Series to A M32.
      Setting controls for the DN9650 can be done on a Mac or PC connected via network cable and accessed through a browser.
      You can not control preamps through the DN9650.
      Some Pro stage boxes can operate at 48kHz so you can directly connect to M32
      These include DL251,231 &15X series

      Bear in mind, the conversion of channels in a DN9650 is 1 to 1, regardless of sample rate. so if to use a KT-AES50 card for M32, you can connect to the primary for 48 bi-directional channels. Using the fixed AES50 ports for Pro series, each connection can only accommodate 24 channels. so port1: 1-24, port2: 25-48.

      at 48kHz the KT-AES50 outputs are duplicated on the secondary port. I'm not aware how it deals with inputs but I suspect will be disabled.

      Lastly, stage boxes can be updated via a computer using IO Updater, found on the website software section of any stage box.

      I hope this answers your questions
      • Feb 15
    • flowaudio
      TobiasWinkl Hi, it ist not possible to use the 48kHz stageboxes DL16/DL32 with the Pro Series Consoles. It works only the other way. You can set the blue ones from 96k to 48k. The Connection has to be direct from the the box to the desk. With the DN9650 and a AES50 card you can downsample the AES50 stream to directly connect a pro desk to a X32/M32.
      • Mar 15
  • New
    Maroliboe
    Contributor - Level 1
    2021-01-29

    Hi Support Team, can I use the DN32-USB card for my Midas M32C like a Midi-interface to controll my Keyboards and Synth from my DAW? Or is this feature implemented in the DN32-LIVE card? (or possible with both cards?) Do you have a Midi implementation Guide for these cards? Thanks and best regards, Martin

    read more...
    0 66
    • Maroliboe
      PedroRodrigues Hi Maroliboe, effectively you can use any of the card you refer on your Midas M32C but not as a MIDI interface, I would suggest following the link below to access information on both cards https://www.klarkteknik.com/klarkteknik/product?modelCode=P0DN1 https://www.klarkteknik.com/klarkteknik/product?modelCode=P0BIF. Thank you
      • Jan 29
    • Maroliboe
      Maroliboe Thank you for your feedback, I have seen this docs, on page 2 in the english product information document you can read at the top: „Your console’s recording capability just got even more robust, thanks to the new DN32-LIVE Expansion Card and USB Audio/ MIDI Interface.“ Is it possible with DN32-Live to send Midi via USB to the Midiports to control external Keyboards/Synthesizers??
      • Jan 29
      • Midi usage DN32-USB vs DN32-LIVE
        Maroliboe ... so is it working like a „true“ midi-interface?
        • Jan 29
      • Midi usage DN32-USB vs DN32-LIVE
        Paul_Vannatto The answer is no. The DN32-Live (as well as the X32-Live) card does not have a midi interface. The console itself has a midi interface that is designed to be used in conjunction with a midi device to control the console (mutes, faders, etc.) only. You are misinterpreting that line in the document. My read is that the DN32-Live expands the recording capability along with the USB Audio (and MIDI interface - for control).
        • Jan 29
    • Maroliboe
      Maroliboe Thank you very much, Paul, for your help :) it helped me in my decision how to route midi in my setup in the best way (and sry for multiple posts :)
      • Jan 31
  • New
    h941224
    Newcomer - Level 1
    2021-01-19

    Is this utilizes Belden tactical Cat 5e cable??

    0 78
    • h941224
      PedroRodrigues Hi , please be aware that any questions regarding Behringer product must be addressed on the Behringer Community page and not on the Kark Teknik community page reserved for question regarding product lines for this bard. Please consider that the NCAT5E-50M is a Cat5e, Neutrik etherFLEX with a RJ-45 EtherCON (not the regular RJ45!) connector. Thank you
      • Jan 19
    • h941224
      GaryHiggins As Pedro said this is Neutrik cable not Belden. I've never bought a Neutrik product ever that wasn't of very high quality . I bought one of these snakes used several years ago and found the quality to be exceptional. It is Beldon tactical equal. Behringer brands/sells them but Neutrik makes the cable and the Ethercon connectors, Hirose makes the shielded rj45 and a Schill makes the reel, all great companies. That said I have been making my own now for quite a while with good success. if I were inclined to buy commercially, this is a very good choice and I would buy it again.
      • Jan 19
  • New
    WillBilliams
    Newcomer - Level 1
    2021-01-16

    I was recently made aware of the bypass on the 76-KT, and was wondering if the KA-2A has an option?

     

    0 70
  • New
    AudioForge
    Newcomer - Level 1
    2021-01-13

    Hi KT team, I've followed a previous post from before Xmas and contacted suppliers re availability of a pair of 2As in a bundle I need.

    Thomann replied with "sold out and not expecting any more". Please can you advise if 2A has been discontinued, I'm ready to order a pair of 2As, a pair of 76s and a dimension.

    richy

    read more...
    0 92
    • AudioForge
      PedroRodrigues Hi Audioforge, please be aware that I can confirm that the units are not discontinued, in regard of availability I would advise you to contact another reseller to request that information about these product as we do not have access to information of third party company that distribute our products. Thank you
      • Jan 14
      • KT2A / 2AKT
        AudioForge Great news, thank you
        • 1
        • ·
        • Jan 14
Go to page