Klark Teknik

Klark Teknik

Brand

Klark Teknik

224,578 members
98,927 posts
  • gtcode
    Contributor - Level 2
    2019-07-17
    Hi, the DN9630 is an AES50 <-> USB interface and this is the closest forum I could find. Does this device really only support 48k and 96k? Doesn't support 44.1 nor 88.2?
    0 468
    • gtcode
      gtcode Answering my own question here - no, it does not support 44.1 -- only 48/96
      • July 17, 2019
    • gtcode
      ChaseMcKnight

      Hi @gtcode 


      Yes, only 96kHz / 48 kHz. The idea behind the DN9630 was to be a lower-cost recording/playback option mainly geared towards our Midas PRO Series users. Prior to the DN9630, users would need to incorportate a Klark Teknik DN9650 w/ Dante or KT-USB card options (or third-party RPM Dynamics interfaces), which are quite expensive if you're simply looking to track shows or use for virtual sound check. 

      The 48kHz option further add to the market for our M/X32 users -- as most people are using the 48kHz sample rate. Further, many of our 'Blue' DL15x, DL25x, DL231 Stageboxes only operate at 96/48 kHz so this is in line with those product ranges. 

      • July 19, 2019
    • gtcode
      gtcode Thanks for your honesty here, However, in responding, you've implied that "it would cost too much to support 44.1k" and "(basically) nobody uses it anyway". Yet, the M32 supports 44.1k, and people do use 44.1k. The DN9630 should have been designed accordingly.
      • July 19, 2019
    • gtcode
      ChaseMcKnight

      Hi @gtcode 

      Apologies, it really wasn't meant to be implied that way. Nearly all AES50 peripherals relating to PRO Series only 96kHz and 48kHz, such as the DN9680, DN9650, DN9620, DN9610, All 'Blue' I/O boxes, and lastly the DN9630. For M/X32 users, I think the majority of applications where a DN9630 would be used would be in the DN32-USB card is replaced with somethng like the DN32-DANTE card -- and typically users set the sample rate to 48kHz. 

      Although it sounds like you were looking for a 44.1kHz solution and in that case, I understand your frustration. 

      • July 19, 2019
    • gtcode
      Dale_M We have an article on this as it gets asked from time to time, https://musictribecommunity.powerappsportals.com/en-us/knowledgebase/article/KA-01573
      • June 24, 2020
  • dexterbalite15
    Contributor - Level 1
    2019-06-27

    When you are using long LAN Cables connecting DM800 to a CP8000 there might be a stability problem in preset and volume have issue like Volume was going up and down or changing preset from 1 to 2 by itself, I solved this problem by adding a Capacitor with value 16Volts/100uF  to the connection of Ground and RVC out at the back of DM8000, Be sure connecting the negative side of the Capacitor to the ground terminal and Positive side of capacitor to RVC pin, I only reccomending this if you having the same problem like what I have experienced otherwise don't add if you don't need this. Also instead of using LAN Cable I recommend to use Belden audio signal (4wires) and there is no more voltage stability issue or faulty preset in this control panel(CP8000).timeline_20190628_101759.jpg

    read more...
    0 292
  • DavidBradshaw
    Solution Leader
    2019-06-06

    Klark Teknik DM DESIGNER 3.1 and DM KONTROL 3.1 are now available for download, via the downloads section on the DM8000 product page.

    DM KONTROL offers PC based customised control page creation and operation of a DM8000 DSP across an ethernet network, when deployed with the new DM801 serial to ethernet bridge.

    Check the downloads here:

    https://www.klarkteknik.com//Categories/Klarkteknik/Signal-Processors/Matrix/DM8000/p/P0B17/Downloads#googtrans(en|en)

    read more...
    1 433
  • Emadson
    Triber Contributor
    2019-05-29

    DM8000 Design 2.9.1 Software and Firmware available for download

    DM8000 Software and Firmware Downloads

    read more...
    0 406
  • Emadson
    Triber Contributor
    2019-05-29

    DM Designer 2.9.1 and Firmware 2.9.1 available for download on KT website

    DM8000 Software and Firmware

    read more...
    1 270
Go to page