Triber

FIRMWARE G3.4.6 (rel-9) IS NOW AVAILABLE FOR THE PRO X

Dear all, 

We are very pleased to announce the release of Firmware G3.4.6 (rel-9) is now available for the Pro X 
(July 30th 2019)

G3.4.6 rel-9 Release Notes

 

New Features

· New Effect: TC Reverb: VSS4

· Presets: Save and overwrite dialogue pop-up

· Presets: Insert patching can be stored and loaded separate to whole system

· Tap Tempo: Pop-up dialogue to type in speed and rate

· Overview/GUI: Automation scenes now displayed in console overview/default for Pro X

· Automation: Scope Key available for Pro X

· Preferences: ‘Output meters pre’ option - distinct from Input meters pre (previous global)

· Preferences: Option to isolate surface navigation buttons

· Preferences: Option to isolate Area B with automate paging

· Show Editor: Mutes and Faders now available as separate options

 

 

Fixes

· DSP: Fixed issue with POST test false errors at boot-up

· DSP: Fixed boot-up issue with keepalive

· DSP: Fixed boot-up issue with race conditions

· Surface/MC: Fixed Surface freeze due to MC application error

· IO/router: Improved issue where IO would not unmute output when connected to NB expansion module and booted up before Neutron. (see below *)

· FX: Fixed issue where M350 reverb recalls settings incorrectly in automation

· Groups: Fixed issue collapse linked outputs could be missing from VCA/POP groups if right linked channel selected

· Groups: Fixed issue Channels could not be removed from POP/VCA via surface if linked input selected

· Flip mode: Fixed issue where FLIP stuck on in Area B when turning off Sync to Area B mid-operation

· Patching: Fixed issue where CM-1 output patching did not update between scenes in automation

· Direct Outputs: Fixed issue where Dir Out showed on surface as patched but would not unmute on scene recall when patched to CM-1

· Solo/Monitor: Fixed - Stereo Aux Sends contribution to monitor bus no longer sums to mono

· FLIP: Can now be selected when no channel is selected on GUI #2

· Detail Strip/GUI: Fixed issue where EQ detail section button could sometimes display Compressor

· FX/Preset: Fixed issue where single effects preset could not be stored

· FX: DEQ frequency value can go out of range when rapidly and significantly changed back and forth.

· Logs: Prevented issue with interlink errors posting rapidly to the logs

 

 

UPDATE PROCEDURE

Update procedure for PRO X console From G3.4.x to G3.4.6 with new Neutron NB expansion module attached.

  1. Download the “.tar” update file for your console
  2. Copy the file PROXG3.4.6rel-9.tar into “DL3upgrades” 
  3. Run the Updater for G3.4.6 via USB as normal
  4. Update full PRO X system from G3.4.x to G3.4.6
  5. Wait for system to display message "Successfully completed update"
  6. Select Quit option and wait for MC to reboot
  7. Power cycle system twice (as per-normal)
Broadcasting Storytelling Champion MUSIC Tribe Brands UK Ltd.
NSomerville Triber 2019-07-31

2019-07-31

FIRMWARE G3.4.6 (rel-9) IS NOW AVAILABLE FOR THE PRO X

Dear all, 

We are very pleased to announce the release of Firmware G3.4.6 (rel-9) is now available for the Pro X 
(July 30th 2019)

G3.4.6 rel-9 Release Notes

 

New Features

· New Effect: TC Reverb: VSS4

· Presets: Save and overwrite dialogue pop-up

· Presets: Insert patching can be stored and loaded separate to whole system

· Tap Tempo: Pop-up dialogue to type in speed and rate

· Overview/GUI: Automation scenes now displayed in console overview/default for Pro X

· Automation: Scope Key available for Pro X

· Preferences: ‘Output meters pre’ option - distinct from Input meters pre (previous global)

· Preferences: Option to isolate surface navigation buttons

· Preferences: Option to isolate Area B with automate paging

· Show Editor: Mutes and Faders now available as separate options

 

 

Fixes

· DSP: Fixed issue with POST test false errors at boot-up

· DSP: Fixed boot-up issue with keepalive

· DSP: Fixed boot-up issue with race conditions

· Surface/MC: Fixed Surface freeze due to MC application error

· IO/router: Improved issue where IO would not unmute output when connected to NB expansion module and booted up before Neutron. (see below *)

· FX: Fixed issue where M350 reverb recalls settings incorrectly in automation

· Groups: Fixed issue collapse linked outputs could be missing from VCA/POP groups if right linked channel selected

· Groups: Fixed issue Channels could not be removed from POP/VCA via surface if linked input selected

· Flip mode: Fixed issue where FLIP stuck on in Area B when turning off Sync to Area B mid-operation

· Patching: Fixed issue where CM-1 output patching did not update between scenes in automation

· Direct Outputs: Fixed issue where Dir Out showed on surface as patched but would not unmute on scene recall when patched to CM-1

· Solo/Monitor: Fixed - Stereo Aux Sends contribution to monitor bus no longer sums to mono

· FLIP: Can now be selected when no channel is selected on GUI #2

· Detail Strip/GUI: Fixed issue where EQ detail section button could sometimes display Compressor

· FX/Preset: Fixed issue where single effects preset could not be stored

· FX: DEQ frequency value can go out of range when rapidly and significantly changed back and forth.

· Logs: Prevented issue with interlink errors posting rapidly to the logs

 

 

UPDATE PROCEDURE

Update procedure for PRO X console From G3.4.x to G3.4.6 with new Neutron NB expansion module attached.

  1. Download the “.tar” update file for your console
  2. Copy the file PROXG3.4.6rel-9.tar into “DL3upgrades” 
  3. Run the Updater for G3.4.6 via USB as normal
  4. Update full PRO X system from G3.4.x to G3.4.6
  5. Wait for system to display message "Successfully completed update"
  6. Select Quit option and wait for MC to reboot
  7. Power cycle system twice (as per-normal)

  • 2 Kudos
  • 0 Replies
  • Reply