Firmware G3.4.2 is now available for PRO1, PRO2, PRO2C, and PRO X!
2017-01-12
01:35 PM
- Subscribe to RSS Feed
- Mark as New
- Mark as Read
- Bookmark
- Subscribe
- Email to a Friend
- Printer Friendly Page
- Report Inappropriate Content
2017-01-12
01:35 PM
Dear all,
We're very pleased to announce the release of firmware G3.4.2 for PRO1, PRO2, PRO2C, and PRO X consoles!
Version G3.4.2
This document constitutes a formal release of Pro 1/2/2C/X software for public usage.
New Features
No new features - this is a bug fix release only
Addressed Issues
- Neutron: Update Neutron DSP Audio FPGA
- Neutron: Update PROX altona layout
- Neutron: Add set command for mgt link 1 on audio fpga
- Effects: Fixed issue where GEQ parameters could cause Spectrum Analyzer to reboot
Update Procedure
Update procedure for Pro X console From G3.2.x to G3.4.2 with new Neutron NB expansion module attached.
N.B. Update of Neutron NB “IO Card” will require Pro X system to be on compatible build before NB module is recognised. This will mean that on the initial update from G3.2.6 or earlier the following steps will be required for a one off update.
1. Download the ".tar" update file for your console
2. Copy the file into "DL1upgrades", "DL2upgrades" or "DL3upgrades" for Pro 1, Pro 2/2C or Pro X respectively
3. Run the Updater for G3.4.2 via USB as normal
4. Update full Pro X system from G3.2.x to G3.4.2
5. Power cycle system twice (as per-normal)
6. Run G3.4.2 updater via USB again
7. Update IO Card to G3.4.2
8. Power cycle system twice
From this point The Neutron NB expansion module (a.k.a “IO Card”) should be recognised by both the Pro X system and the Pro X updater app (USB updater).
Once the system has reached this point the whole system, including the Neutron NB expansion module, can be updated in the regular way with only one pass of the updater application.
Update procedure for
- Pro 1
- Pro 2 and Pro 2C
- Pro X system WITHOUT Neutron NB installed
- Pro X system WITH Nuetron NB and G3.4 or G3.4.1 already installed
Regular update procedure using USB stick
1. Download the ".tar" update file for your console
2. Copy the file into "DL1upgrades", "DL2upgrades" or "DL3upgrades" for Pro 1, Pro 2/2C or Pro X respectively
3. Run the Updater for G3.4.2 via USB as normal
4. Update full Pro X system to G3.4.2
5. Power cycle system twice (as per-normal)
We're very pleased to announce the release of firmware G3.4.2 for PRO1, PRO2, PRO2C, and PRO X consoles!
Version G3.4.2
This document constitutes a formal release of Pro 1/2/2C/X software for public usage.
New Features
No new features - this is a bug fix release only
Addressed Issues
- Neutron: Update Neutron DSP Audio FPGA
- Neutron: Update PROX altona layout
- Neutron: Add set command for mgt link 1 on audio fpga
- Effects: Fixed issue where GEQ parameters could cause Spectrum Analyzer to reboot
Update Procedure
Update procedure for Pro X console From G3.2.x to G3.4.2 with new Neutron NB expansion module attached.
N.B. Update of Neutron NB “IO Card” will require Pro X system to be on compatible build before NB module is recognised. This will mean that on the initial update from G3.2.6 or earlier the following steps will be required for a one off update.
1. Download the ".tar" update file for your console
2. Copy the file into "DL1upgrades", "DL2upgrades" or "DL3upgrades" for Pro 1, Pro 2/2C or Pro X respectively
3. Run the Updater for G3.4.2 via USB as normal
4. Update full Pro X system from G3.2.x to G3.4.2
5. Power cycle system twice (as per-normal)
6. Run G3.4.2 updater via USB again
7. Update IO Card to G3.4.2
8. Power cycle system twice
From this point The Neutron NB expansion module (a.k.a “IO Card”) should be recognised by both the Pro X system and the Pro X updater app (USB updater).
Once the system has reached this point the whole system, including the Neutron NB expansion module, can be updated in the regular way with only one pass of the updater application.
Update procedure for
- Pro 1
- Pro 2 and Pro 2C
- Pro X system WITHOUT Neutron NB installed
- Pro X system WITH Nuetron NB and G3.4 or G3.4.1 already installed
Regular update procedure using USB stick
1. Download the ".tar" update file for your console
2. Copy the file into "DL1upgrades", "DL2upgrades" or "DL3upgrades" for Pro 1, Pro 2/2C or Pro X respectively
3. Run the Updater for G3.4.2 via USB as normal
4. Update full Pro X system to G3.4.2
5. Power cycle system twice (as per-normal)
Brands:
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Latest Articles
- [Khoros Community] - Issue with embedding YouTube ...
- Recognizing our Top Contributors
- Flashback 2 now has built-in Tap Tempo
- 30 years in the making. What will it be?
- Lab Gruppen Introduces PDX3000 Amplifier
- Tannoy New Product Announcement
- Tannoy New Product Announcement
- Care Portal
- Go Guitar Pro Is In Stores Now & Pairs perfectly w...
- Behringer is Now Officially Europe’s Number 1 Bran...