We're very pleased to announce the release of firmware G3.4 for PRO1, PRO2, PRO2C, and PRO X consoles!
Version G3.4 (25 May 2016)
This document constitutes a formal release of PRO1/2/2C/X software for public usage.
Neutron NB expansion card - 10 x additional AES50 SMAC ports - Fully configurable ports work as an expansion of the existing standard 8 AES50 ports on the Neutron and three FoH AES50 ports on the PRO X surface - 2 x CM-1 expansion ports - ASRC allows for separate external clock sync of module (card dependent) - Or module and it’s network can clock from Neutron - Allows for the configuring of the following CM-1 modules - KLARK TEKNIK MADI - KLARK TEKNIK USB - KLARK TEKNIK AES50 - Audinate Dante 64
New Effects - Automixer - TC Electronic M350 Reverb
Auto Config - Option in Config dialogue pop up (Diagnostics page only) - Automatically configures all connected IO units - Non-destructive update, will leave pre-configures slots and patching unchanged - Additional option to un-configure all current units (and patching)
PRO Xb Support
Mono master link to Stereo Masters (PRO1)
ADDRESSED ISSUES - Surface: Resolved and issues where surface could occasionally freeze for 5-10 sec when unfolding user mode POP/VCA groups with Overlay Stereo Pairs - DL231: Fixed and stabilised output configuration from B side - DL231: Now able to configure outgoing MIDI via AES50 - DL231: Resolved diagnostics errors when PRO1 or 2 connected to B side of DL231 with PRO 369X connected to A side - Diagnostics: Correction to 5V -10% tolerance - Automation: Direct outs recalled correctly with store/recall scopes - Automation: +48 V no longer causing clicks on occasion when used with store/recall scopes - Talk/Osc: audio only routed to left channel of two linked channels - MIDI: Improvements to existing MIDI functionality - Effects: De-esser bypass button realigned - DL451: redundant swap back to X (primary) from Y (redundant) resolved - D-Sub: Fixed issue with gain control for D-Sub on DL351 and DL451 - Automation: Solos no longer clear on scene change - Naming Sheet: Fixed issue where selecting Input 1-16 from drop down menu would call AuxS 1-16 instead - Shutdown system: monitor log now separated from boot log. - Shutdown system: Improved shutdown sequence will result in surface going green in under a minute. - Effects: Metering no longer seen for unpatched channels in effects - GUI: Contributions to AuxS now correctly displayed following input mode change - GEQ: Linked stereo GEQ can now be flattened from surface in GEQ mode - IO Config: Resolved issue where PRO1 could start up in state where IO unit ID number could not be selected
Update procedure for PRO X console From G3.2.x to G3.4 with new Neutron NB expansion module attached.
NB module is recognised. This will mean that on the initial update from G3.2.6 or earlier the following steps will be required for a one off update.
1. Download the “.tar” update file for your console 2. Copy the file into “DL1upgrades”, “DL2upgrades” or “DL3upgrades” for PRO1, PRO 2/2C or PRO X respectively 3. Run the Updater for G3.4 via USB as normal 4. Update full PRO X system from G3.2.x to G3.4 5. Power cycle system twice (as per-normal) 6. Run G3.4 updater via USB again 7. Update IO Card to G3.4 8. Power cycle system twice
From this point The Neutron NB expansion module (a.k.a “IO Card”) should be recognised by both the PRO X system and the PRO X updater app (USB updater).
Once the system has reached this point the whole system, including the Neutron NB expansion module, can be updated in the regular way with only one pass of the updater application.
Update procedure for PRO1 and PRO2/2C consoles as well as PRO X system WITHOUT Neutron NB installed From G3.2.x to G3.4
Regular update procedure using USB stick
1. Download the “.tar” update file for your console 2. Copy the file into “DL1upgrades”, “DL2upgrades” or “DL3upgrades” for PRO1, PRO2/2C or Pro X respectively 3. Run the Updater for G3.4 via USB as normal 4. Update full PRO X system from G3.2.x to G3.4 5. Power cycle system twice (as per-normal)