2019-11-19
06:48 PM
I'm not sure if someone already asked but I'm trying to accomplish the following: I have (2) M32's, (1) M32R and a (2) DL32's. I can accomplish what i need with an analog split and (2) DL32's but want to use AES50 with a single DL32. I would like to use (1) DL32 on stage with a M32 at FOH and a M32R at monitors. I would like the M32R monitor console to have gain control and the FOH to have digital trim. Is it possible to have XLR outputs 1-12 on the DL32 routed from the M32R for 12 analog monitor mixes and AES outputs 13-14 on the back of the DL32 from the FOH console M/C and AES outputs 15-16 on the back of the DL32 from the FOH console L/R mains. My current setup is a M32 with a DL32 for FOH and montors with 12 analog montor mixes and AES 13/14 for M/C and AES 15/16 for L/R Mains. If this will work, i may purchase a M32C to replace the M32R as my monitor console. Thank you
Read more
2019-04-05
04:36 PM
I will double check my M32 routing on the AES50A tab next week. I'm assuming it's setup correctly. Thanks,
Read more
2019-04-05
04:11 PM
I have a M32 connected to a DL32 and having problems setting up Aux 9 through 12 as monitor mixes. I have mixes1 through 8 working for wedges but not able to get sound out of Aux 9 to 12 for IEM's. I had to disconnect amps from mixes 8 and below to plug in the IEM's. I'm also not able to get Aux 9 -12 working from a M32R through a DL32. Any help would be appreciated
Read more
Brands:
2016-04-07
02:59 PM
Craig, Thanks for the great information I'm going to re-configure my Midas console before this weekend's festival. I'm running 5 stages and have a mix of Midas, Soundcraft, Allen & Heath and mackie consoles. The A&H is the only analog console with old school rack of eq's and efx. My plan is to migrate to more Midas consoles and begin selling off the others.
Read more
2016-04-06
10:28 AM
Thanks for the information. I've only had my console for 6 months, used it a few times and still trying to figure out how to navigate through all the settings. Festival season is beginning and I need to learn this in a few days. When I purchased the console 6 months ago, Using it for the first time was like jumping into a fire and hope to survive. The quick setup guide is very basic and the owners manual doesn't go into detail on each subject. The manual assumes that the users knows what LC and +M, Tap, routing, etc. means. It would be great is their technical writer can add visual descriptions like the attached drawing into the manual. Running my monitors from FOH (with ipad on stage), I prefer to have everything pre (just like an analog console). I assume In/LC in the signal patch is input/low cut on each channel strip Just to clarify. For the input stage. my Home/Config (channel sends preconfiguration) should be set for IN/LC with a TEQ inserted. This should make the mixbus all pre, with the exception of the LC. The Routing/Out 1-16 should be set for Output x/ Mix Bus / MixBus 0x/Post Fader. this will make the mixbux post fader (bus 1-8 faders on the right of the console) What does the Setup/Config (Bus Pre-configuration) do? When I select 8+0+8, mixbus 1-8 will be defaulted to Post-EQ and mix bux 9-16 setup for post-fader. Each channel strip also has a setting in the Home/sends where the mix bus can be changed. Do I need to make changes to all to get it to work correctly? Making changes to the Mixbus 1/home/config doesn't seem to change the mixbus setting on the channel strip home/send tab. I currently have my tap at pre-fader and my output at pre-fader since this is how I'm used to setting up my analog consoles. I'm not sure if the monitors are affected by the channel EQ. I will setup my console this week and reconfigure the mixbus tap for In/LC and post-fader on the output it for the upcoming weekend festivals.
Read more
2016-04-05
12:41 PM
I read through the manual but there was not a clear explanation on how to do this: How do I setup my console so my mix bus 1 - 10 are all pre (pre-fader, pre-eq, pre dynamics). There is a config section in the "setup" with a "Bus Pre-configuration" where I can select 10+0+6 but the 10 are set for post eq and the 6 are set for post fader. I need this for monitor sends. I will be inserting graphic EQ's from the effects section into mixbus 1-6 Under "Routing, Out 1-16" There are many Tap options (IN/LC, IN/LC + M, PreEQ, PreEQ+M, PostEQ, PostEQ+M, PreFdr, PreFdr+M, Post Fader. Not sure what these are for. Is the "M" mute?
Read more
Brands: